Cardin Elettronica SL Série Manuel D'instructions page 16

INSTRUCTIONS FOR POSITIONING THE UNIT
7
- The geared motor unit has been assembled in
the factory to be fitted to the LEFT SIDE of the
gate (internal view). To install the motor to the
RIGHT of the gate set dip 8 of the dip-switch
DS1 ON
MANUAL MANOEUVRE WITH THE MOTOR RELEASED
Manual release is to be carried out with the motor Stopped. To release
the gate use the manual release key supplied with the unit. The key
should be kept in an easily accessible place.
To release the unit
1. Rotate the lock protection disk on the
release knob, insert the key and rotate it
half a turn anticlockwise. The knob is now
free and can be released.
2. Rotate the knob through 90° clockwise. The
gears are now released and the gate can be
moved manually.
To relock the unit
1. Rotate the handle anticlockwise and move it back to the blocked
position.
2. Rearm the gears:
- electrically by giving an opening or closing command;
- by slightly moving the gate
3. Rotate the key clockwise and relock the handle.
Once the system has been reset store the key in a safe place.
Attention! Never use the manual release mechanism while
the gate is in operation. If you release the gate and then give
a movement command the following symbol will appear
on the display .
Access to the electronic card
9
Attention! Before opening the cover make
sure that the power has been switched off
at the mains.
To access the motor loosen the two screws
A
A
indicated in figure 9.
ELECTRONIC PROGRAMMER
Electronic programmer for a dc motor with an incorporated radio
receiver card, which allows the memorisation of 300 user codes (see
MHz series transmitters.
The motor rotation speed is electronically controlled, starting slowly
and increasing in speed; the speed is reduced as it nears the travel
limit so as to enable a controlled smooth stop.
Programming is carried out using one button and allows you to set the
system, the current sensor and the entire gate travel distance.
The logic carries out position control using an encoder.
The intervention of the anticrush/antidrag sensor during the closing
and opening stages causes a brief (10 cm) travel direction inversion
then a block.
ON
1 2 3 4 5 6 7 8 9
8
Mains power supply connection
the bottom right of the main circuit board and to the separate 3-way
terminal board:
- connect the neutral to binding post N
- connect the earth to binding post
- connect the live to binding post
433.92
16
IMPORTANT REMARKS
programmer, release the gate (manual release mechanism) and
move it manually, checking that it moves smoothly and has no
unusual points of resistance.
indicated by the warning lights pre-flashing for 10 seconds, and by
the symbol
ing
system, which is used to block the motor in emergency conditions;
however this system is not active during the following stages:
- during the first 5 s of an opening stage starting from completely
closed
- during the first 2 seconds of all other movement stages
- when the battery undercharged
Do not therefore attempt to physically block the door during these
stages, otherwise you may risk blowing the motor circuit protec-
F1
power supply to the programmer; reconnect it only after having
re-inserted the fuse.
The presence of the electrical input monitoring system does
not exclude the need to install photoelectric cells or other safety
devices which are foreseen by the local standards and regulations
in force.
The geared motor unit has been assembled in the factory to be
for positioning the unit
For the correct operation of the programmer the incorporated
batteries must be in good condition: the programmer will lose the
position of the gate in case of blackouts when the batteries are flat,
the alarm will sound and automatic repositioning will take place .
Check the good working order of the batteries every six months
Battery check
frequency rated on the data plate conform to those of the mains
supply.
must be installed between the unit and the mains supply.
ends of cables which are to be inserted into the binding posts; use
cables marked T min 85°C and resistant to atmospheric agents.
the wire and the insulating sheath are tightly fastened (a plastic
jubilee clip is sufficient).
before powering up the
automatic reposition-
F2
instructions
3 mm between the contacts
N
L
L