Preliminary Check; Hot Water - Sanremo CAPRI XLC SAP Livret D'instructions

Table des Matières

Les langues disponibles

ENGLISH

N.B. A water softener is indispensable for correct appliance operation, best coffee in the cup and long life of the components, since it removes scale and

residues from the water that would otherwise shorten their life.

The company is relieved of all and any liability in the event of failure to comply with the above instructions.

Open the tap and let water ﬂ ow through the deconcentrator to clear dirt off the circuit before plugging the hose into the pump.

Before using the appliance, check that:

- the plug is inserted properly into the mains power outlet;

- the water ﬁ lling hose is correctly connected to the mains water outlet, check for leaks and that the water tap is open;

- the drain pipe is positioned in accordance with the preceding instructions.

With a steam tap (B) open, put the on/off switch (D) to position 1 and wait for the water in the boiler to reach the

maximum level set by the electronic control. If the boiler does not ﬁ ll within the set time-out (90 sec.), the pump stops

and the indicator lights on the keypad start to blink. In this case put the on/off switch (D) to position 0 and then to

position 1 to ﬁ nish ﬁ lling the boiler.

Now put the on/off switch (D) to position 2 so that the heating elements are powered and therefore start to heat the

water.

Wait for steam to come out the steam nozzle (B), then close the tap and, using the Boiler pressure gauge, check that

the pressure has reached and maintains a value of 0.8:1 bar. If it is not on this value, turn the adjusting screw on the

pressure switch (+increase, - decrease, see ﬁ gure below).

Ensure that the boiler pressure gauge indicates a pressure of 0.5:1 bar. Turn the tap knob (C) counter-clockwise.

Pay the utmost attention in order to prevent scald burns.

Except for the 1-group machine that has just one steam nozzle, all the other models have 2 located at the sides. These steam nozzles are recessed but can

swivel out thanks to an articulated joint. To dispense steam, just turn the knobs (B) counter-clockwise.

Pay the utmost attention in order to prevent scald burns.

Insert the ﬁ lter holder (E) into the group head (F) turning the ﬁ lter holder counter-clockwise. Press button (I), wait for the required quantity of coffee to be

dispensed and then put it back to its original position.

Insert the ﬁ lter holder (E) into the group head (F) turning the ﬁ lter holder counter-clockwise. Select the type of dispensing required on the keypad (M):

M1=One strong/normal coffee.

M2=One normal/weak coffee.

M3=Two strong/normal coffees.

M4=Two normal/weak coffees.

M5=Electronic programming key or continuous manual dispensing.

a) To access this phase keep the button M5 on the ﬁ rst pushbutton panel on the left pressed for over 5 seconds. The indicator lights of the buttons M5 start

to blink continuously. Select the caption corresponding to the amount required and press to dispense. The indicator light of button M5 and that of the

selected caption remain lit. When the required amount has been dispensed, press the selected dispensing button again so that the control unit stores the

data. Repeat the above procedure for all 4 dispensing buttons on the pushbutton panel. A dispensed quantity may also be set for the hot water button

(M6) by repeating the above procedure. Upon completion of the procedure, the remaining groups will automatically use the stored quantity. The other

groups may, however, be programmed independently by repeating the same procedure as above after having programmed the ﬁ rst group on the left.

b) There are 2 safety systems inside the control unit designed to protect the electronic system and the various parts of the appliance. If, upon pressing a

dispensing button, the corresponding indicator light starts blinking, this indicates a malfunction in the electronic system or lack of water. For safety

reasons, the dispensing of water stops after 4 minutes and in any case after 4 litres of water.

c) The CAPRI XLC SED electronics also offers the possibility of reproducing the pre-brewing effect by wetting the coffee for 0.6 seconds and then stopping

the subsequent brewing from starting for 1.2 seconds. This option is only applicable for single shots of coffee.

USE