Technical Specifications - IKRA ATHS 2440 Manuel D'utilisation

Telescopic hedge trimmer - battery ATHS 2440

Technical specifications

Rated-Voltage
No-load-Speed-n
0
Maximum-cutting-length
Maximum-cutting-diameter
Angle-at-which-the-motor-can-be-set--
Tool-length
Working-height
Weight-with-bar+chain
Sound Pressure Level-(
Acoustic-capacity-level--L
Vibration-(
EN-ISO-10517)
Mains battery charger
Mains-voltage
Charging-voltage-/-Charging-current
Period-of-charging
Technical-changes-are-reserved.
The-specified-vibration-emissions-value-is-measured-in-accordance-with-EN-ISO-10517.-This-can-be-used-for-any-
other-hedge-trimmer-with-the-same-design-and-type-of-power-supply.
The-specified-vibration-emissions-value-limits-the-working-time.-Stop-working-if-you-notice-a-tingling-sensation-or-a-
discolouration-(white)-of-the-fingers.
WARNING: When-in-operation,-the-tool's-actual-vibration-emissions-value-can-deviate-from-the-specified-value-de-
pending-on-how-the-tool-is-used,-as-in-the-following-examples-or-because-it-is-used-in-another-way:
- - How-the-tool-is-being-used-and-which-materials-are-being-cut.
- - The-tool-is-well-maintained-and-in-good-working-order.-The-correct-accessories-are-being-used-and-care-has-been-
taken-to-make-sure-they-are-sharp-and-in-good-working-order.
- - How-secure-the-hand-grip-is-and-whether-anti-vibration-accessories-are-being-used.
- - Whether-the-tool-is-being-used-in-accordance-with-its-design-and-as-specified-in-these-instructions.
- - The-tool-can-cause-hand-arm-vibration-syndrome-symptoms-if-it-is-not-used-properly.
WARNING: To-make-sure,-an-assessment-should-be-made-of-the-strain-exerted-when-the-tool-is-in-use,-for-example-
when-the-tool-is-switched-off-or-is-idling.-This-will-make-it-possible-to-significantly-reduce-the-strain-exerted-during-the-
entire-time-the-tool-is-in-use.
Minimise-your-risks-if-the-tool-vibrates.
Take-care-of-the-tool-as-specified-in-these-instructions-and-make-sure-the-tool-is-properly-lubricated-(if-necessary).
If- the- temperature- is- 10°C- or- less,- do- not- use- the- tools.- Prepare- a- work- schedule- so- that- work- is- distributed- over-
several-days-when-using-tools-that-exert-high-vibrations.
Noise-emission-information-in-accordance-with-the-German-Product-Safety-Act-(ProdSG)-and-the-EC-Machine-Direc-
tive:-the-noise-pressure-level-at-the-place-of-work-can-exceed-80-dB(A).-In-such-cases-the-operator-will-require-noise-
protection-(e.g.-wearing-of-ear-protectors).
Attention: Noise protection! Please-observe-the-local-regulations-when-operating-your-device.
EN-ISO-10517)
(20001/14/EG)
wA-
-
24-V-DC-/-1,9-Ah-/-45,6-Wh
-1
2200---3000-min
400-mm
18-mm
0°-to-135°
from-1.95-m-to-2.35-m
up-to-3.5-m
4.2-kg
82-dB(A)----
K-=-2,5-dB
95-dB(A)----
K-=-2,6-dB
2
<2,5-m/s --- 2
K-=-1,5-m/s -
230-V~-/-50-Hz
25,2-V-DC-/-500-mA
approx-3---5-hour
GB-4