Table des Matières
Publicité
Send and receive references through the serial line.
There is a new feature for sending receiving the reference tables through the serial line.
The format for the reference table is the following:
01 X10.000 Z0.000 X- Z- d X/Z
02 X20.000 Z15.000 X+ Z- r X/Z
03 X30.000 Z45.000 X- Z- d X/Z
04 X0.000 Z0.000 X- Z+ r
05 X50.000 Z14.000 X+ Z+ r
06 X60.000 Z0.000 X- Z+ d
07 X70.000 Z0.000 X+ Z+ r
08 X80.000 Z0.000 X- Z- d X/Z
09 X90.000 Z0.000 X- Z- d
10 X0.000 Z0.000 X- Z+ d
11 X0.000 Z0.000 X+ Z+ r
12 X0.000 Z0.000 X+ Z+ r
13 X0.000 Z0.000 X+ Z- r
14 X0.000 Z0.000 X+ Z+ r
15 X0.000 Z0.000 X+ Z+ r
16 X0.000 Z0.000 X+ Z+ r
17 X0.000 Z0.000 X+ Z+ r
18 X0.000 Z0.000 X+ Z+ r
19 X0.000 Z0.000 X- Z+ r
20 X0.000 Z0.000 X+ Z+ r
21 X0.000 Z0.000 X+ Z- d X/Z
22 X0.000 Z0.000 X- Z- d X/Z
23 X0.000 Z0.000 X+ Z+ r
24 X0.000 Z0.000 X+ Z+ r
25 X0.000 Z0.000 X- Z+ r
26 X0.000 Z0.000 X+ Z+ r
00 $ indicates the end of transmission.
All references need not be sent. The DRO may receive just the specific ones.
For example:
01 X10.000 Z0.000 X- Z- d X/Z
02 X20.000 Z15.000 X+ Z- r X/Z
03 X30.000 Z45.000 X- Z- d X/Z
04 X0.000 Z0.000 X- Z+ r
05 X50.000 Z14.000 X+ Z+ r
PARAMETERS
There are 2 new parameters:
1.Par 60, indicates how to apply the references. The default value is "0".
0 = It applies the value of the reference and its properties on the normal position reading. In other words, it applies the
offsets and properties of the associated reference to the value of the calibrated tool both in normal position display and
when editing.
1, 2, 3 in these modes, the value and properties of the reference associated to the tool position reading and display.
2. par 64 is described in the other document.
Bit 1
Enter in Search Io mode automatically on DRO power on, DEFAULT = 1
Bit 2
Use a new VFD display( blue color, with new characters) DEFAULT = 1
Bit 3
Use a password to edit REFs. DEFAULT = 1.The password is 719200
Bit 4
Ask for one reference number each time you measure a tool.
- FAGOR AUTOMATION S. COOP -
27 X0.000 Z0.000 X+ Z+ r
28 X0.000 Z0.000 X+ Z+ r
29 X0.000 Z0.000 X+ Z+ r
30 X0.000 Z0.000 X- Z- d
31 X0.000 Z0.000 X- Z+ r X/Z
32 X46.000 Z25.000 X- Z+ d X/Z
33 X111.110 Z222.222 X- Z- d X/Z
34 X0.000 Z0.000 X+ Z+ r X/Z
35 X0.000 Z0.000 X- Z- d
36 X0.000 Z0.000 X- Z+ d X/Z
37 X0.000 Z0.000 X+ Z+ r X/Z
38 X0.000 Z0.000 X+ Z+ r
39 X0.000 Z0.000 X+ Z+ r X/Z
40 X0.000 Z0.000 X- Z+ d
41 X0.000 Z0.000 X- Z- d
42 X0.000 Z0.000 X+ Z+ r
43 X0.000 Z0.000 X- Z+ d X/Z
44 X0.000 Z0.000 X+ Z+ d X/Z
45 X0.000 Z0.000 X+ Z- r X/Z
46 X0.000 Z0.000 X+ Z+ r
47 X0.000 Z0.000 X+ Z+ r
48 X0.000 Z0.000 X+ Z+ r
49 X0.000 Z0.000 X+ Z+ r
50 X0.000 Z0.000 X+ Z+ r
51 X0.000 Z0.000 X- Z- d
06 X60.000 Z0.000 X- Z+ d
50 X0.000 Z0.000 X+ Z+ r
51 X0.000 Z0.000 X- Z- d
- Page 5 of 5 -
00 $
00 $
Publicité
Table des Matières
