Master Chef PROPANE SMOKER Manuel D'assemblage page 7

ASSEMBLY, ASSEMBLAGE
3
A
x4
A
6
4
B
x4
B
20
B
17
Align venturi over valve orifi ces and attach ignition wire to piezo ignitor on
control panel.
Alignez soigneusement le tube de Venturi aux orifi ces du robinet et fi xez
solidement les fi ls d'allumage au dispositif d'allumage piézo sur le panneau
de contrôle.
Venturi
Tube
de Venturi
Valve Orifi ce
Orifi ce de la valve
Ignition Wire
Fil du dispositif
d'allumage
Piezo Ignitor
Dispositif
d'allumage piézo
5
A
x4
1
8
A
IGNITION INSTRUCTIONS
REGULATOR, BURNER AND GAS VALVE CONNECTION & OPERATION
• Inspect hose before each use. If there are signs of abrasion, wear, cuts, or leaks, the hose must
COUNTER
be replaced. DO NOT USE.
CLOCKWISE CLOCKWISE
CLOCKWISE
• Inspect burner before each use. Check burner and burner venturi tube for insects and insect
nests. A clogged tube can lead to a fi re beneath unit.
• Check to ensure the orifi ce is centred inside the venturi tube. Failure to properly assemble
Fig. 1
the valve orifi ce to the venture tube can result in gas leak or potential fi re at connection. See
assembly steps for proper assembly method.
• Connect hose regulator to LP Gas Cylinder (Fig. 1)
1. Make sure gas cylinder valve is closed. Turn valve clockwise until it stops.
17.75"
(45cm) 2. Make sure burner control valve on smoker is in the OFF position.
APPROX.
3. Remove protective cap from gas cylinder and coupling nut if applicable.
4. Centre and insert regulator nipple into valve outlet on gas cylinder as shown in fi gure on the
left. Turn regulator coupling nut clockwise until it stops. DO NOT OVER TIGHTEN.
12.25" (45cm)
• Perform SOAPY WATER TEST.
APPROX.
• Before starting lighting procedure make sure the smoker door(s) are open.
• When lighting burner remove all parts inside or on unit to prevent explosion from gas build up.
Fig. 2
• To use, turn gas cylinder valve ON, push burner control valve in and turn counter-clockwise 1/4
turn to HIGH setting. Push ignitor button to light.
• If ignition does not take place within fi ve seconds, turn burner control valve to OFF position and
wait fi ve minutes and repeat lighting procedures. If ignition still does not occur, see match light
instructions.
• Always ensure that smoker door(s) are open before igniting. Gas can accumulate in smoker.
• If fl ame goes out during cooking, turn burner control valve OFF, turn gas cylinder valve OFF, wait
5 minutes, then open door(s) and wait 5 additional minutes before repeating ignition instructions
above.
• Burner control valve adjusts burner fl ame. Turn valve counterclockwise to decrease fl ame. Turn
valve clockwise SLOWLY to increase fl ame. Push burner control valve in and turn clockwise to
Fig.4
shut fl ame off.
• Visually check burner fl ame (Fig. 2). A CORRECT FLAME should be blue with a small amount of
yellow at the tip. An INCORRECT FLAME is excessively yellow and irregular. If an incorrect fl ame
occurs, turn burner control valve to OFF position, turn OFF gas cylinder valve. If an incorrect
fl ame still occurs allow unit to cool and then clean burner. Let burner completely dry before re-
lighting.
• After use turn burner control valve OFF, then turn gas cylinder valve OFF and disconnect tank.
• Type 1 Regulators will have a hook (Fig. 4). The Regulator Hook is used to keep the regulator off
the ground when removed from the LP cylinder. Attach to unit as shown in image.
MATCH LIGHT INSTRUCTIONS
1. Read all instructions and warnings before lighting.
2. Check burner control valve and gas cylinder valve to be certain it is in OFF position
before connecting to gas cylinder.
3. Perform SOAPY WATER TEST before each use.
4. Open door(s) during lighting and/or remove all accessories and cooking vessels from
in/or on unit.
5. Turn gas cylinder valve on, then turn burner control valve on.
6. Place a long, lit fi replace match stick close enough to burner to ignite.
7. If ignition does not take place within fi ve seconds, turn burner control valve to OFF
position and wait fi ve minutes and repeat match light instructions.
8. After each use, fi rst turn burner control valve off, then gas cylinder valve off. Always
allow unit to cool completely before touching, moving or storing. 6