Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
FIREBALL
Upon the first ignition we suggest loading a reduced quantity of fuel and slightly increasing the calorific
value of the equipment.
To perform a correct first lighting of the products treated with paints for high temperature, it is necessary to
know the following information:
•
the construction materials of the involved products are not homogeneous, as matter of fact there
are simultaneously parts in cast iron, steel, refractory material and majolica;
•
the temperature to which the body of the product is subject is not homogeneous: from area to
area,variable temperatures within the range of 300°C - 500 ° C are detected;
•
during its life, the product is subject to alternated lighting and extinguishing cycles in the same
day, as well as to cycles of intense use or of absolute standstill when season changes;
•
the new appliance, before being considered seasoned has to be subject to many start cycles to
allow all materials and paints to complete the various elastic stresses;
•
in detail, initially it is possible to remark the emission of smells typical of metals subject to great
thermal stress, as well as of wet paint. This paint, although during the manufacture it is backed at
250 ° C for some hours, must exceed many times and f or a given period of time the temperature of
350 ° C before becoming completely embedded in the m etallic surfaces.
Therefore, it is extremely relevant to take these easy steps during the lighting:
1) Make sure that a strong air change is assured in the room where the appliance is installed.
2) During the first starts, do not load excessively the combustion chamber (about half the quantity
indicated in the instructions manual) and keep the product continuously ON for at least 6-10 hours
with the registers less open than the value indicated in the instructions manual.
3) Repeat this operation for at least 4-5 or more times, according to your possibilities.
4) Then load more and more fuel (following in any case the provisions contained in the installation
booklet concerning maximum load) and, if possible, keep the lighting periods long avoiding, at least
in this initial phase, short ON/OFF cycles.
5) During the first starts, no object should be leaned on the appliance and in detail on
enamelled surfaces. Enamelled surfaces must not be touched during heating.
Once the «break-in» has been completed, it is possible to use the product as the motor of a car,
6)
avoiding abrupt heating with excessive loads.
To light the fire, it is suggested to use small wood pieces together with paper or other traded lighting
means.
It is FORBIDDEN to use any liquid substance as for ex. alcohol, gasoline, oil and similar.
The primary air register has to be opened, so lever completely pulled out (Picture 1 - 1). When wood starts
to burn, it is possible to feed it again, close the primary air control (completely pushed to the back) control
the combustion through the secondary air register (Picture 1 - 2) according to the provisions of CHAP. 10.
Please always be present during this phase.
Never overload the appliance (see the technical table - max. quantity of fuel that can be loaded / hourly
consumption .
Too much fuel and too much air for combustion can cause overheating and therefore damage the
same.
10.
NORMAL OPERATION
For safety reasons the door of the appliances with constructive system 1, must be opened only for the
loading of the fuel or for removing the ashes, while during the operation and the rest, the door of the hearth
must remain closed.
The appliances with constructive system 2 must be connected to their own flue. The operating with open
door is allowed under supervision.
IMPORTANT: For safety reasons the door of the hearth can be opened only for the loading of the
fuel. The hearth door must always remain closed during operation or rest.
The nominal power of the appliance is of 6 kW. This power will be reached with a minimum depression in
the chimney of 12 Pascal (=1.2 mm of water column).
With the registers located on the front of the appliance (Picture 1), it is possible to adjust the heat emission
of the same. They have to be opened according to the calorific need. The best combustion (with minimum
7196801 Rev.07 – EN
23
Publicité
Table des Matières
