Bort BSS-2400N Mode D'emploi page 8

Masquer les pouces Voir aussi pour BSS-2400N:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

12. Before using the cleaner, please remove big and
sharp matters on the fl oor to avoid damaging the plas-
tic parts, fi lter gauzes and motor.
13. Never absorb water or other liquid with this cleaner,
otherwise, the motor will be damaged.
14. This appliance is not intended for use by persons
(including children), with reduced physical, sensory or
mental capabilities, or lack of experience and knowl-
edge, unless they have been given supervision or in-
struction concerning use of the appliance by a person
responsible for their safety.
ASSEMBLY INSTRUCTIONS
Always remove the plug from the power socket before
fi tting or removing accessories!
1. Equiping vacuum cleaner
1. Fixing the fl exible hose on vacuum machine:
REPLACEMENT OF REAR
FILTER FOR MOTOR
The rear fi lter for motor is installed behind the air outlet
grid, which can be washed due to the materials used.
When the surface is jammed seriously by dust, the fi lter
should be replaced by a new one or washed by water
to maintain enough suction force.
It is usually necessary to clean and replace the fi lters
for motor only after they have been used for 6 months
to 12 months. Please remember to confi rm that all
fi lters have been correctly installed into the machine
before turning on the cleaner to use.
Key Points:
The power supply of the cleaner must be cut off before
replacing any fi lter!
FAULTS AND REPAIR
In case of abnormality with this product, please treat
it in the way as stated hereinafter; if the cleaner still
refuses to work normally, please contact the stop from
where this product was bought or with the appointed
service point.
Insert hose joint into the air intake duct on the front of
appliance. Press until it clicks into position.
( Attention: The fl exible hose must be fi xed into the
vacuum body, then the vacuum can work. Otherwise,
the vacuum can't work without the fl exible hose fi xed
in.)
** Removing the fl exible hose from vacuum machine:
Removing the plug from the power socket. Press
release button on hose joint to remove the fl exible hose
from the vacuum machine.
2.Fixing the extension tubes and accessories
a. Fixing the telescopic tube to the handle.
b. Fixing the brush to the extension tube.
c. Fixing Floor brush Ideal for the daily cleaning on
carpets and hard fl oors.
8
2.Cleaning tools use
1. Crevice tool:
For radiators, crevices, corners, baseboards and
between cushions.
2. Dusting brush(2 in 1 ) is used for the furniture,
venation, blinds, book, lamp shades and shelves,etc.
Separately it can be used as a sofa nozzle.
INSTRUCTIONS FOR USE
Before using appliance, pull out a suffi cient length
of cable and insert the plug into the power socket. A
yellow mark on the power cable shows the ideal cable
length. Don't expend the cable beyond the red mark.
1. Switch Button
Insert the power plug into the socket. Press the main
ON/OFF Switch button on vacuum body to switch on
the vacuum machine, then the power indicating lamp
(neo-lamp) will be lighting, it is ready for work.
Then you can slide the power button on the hose handle
to switch on and adjust the power of this vacuum.
2. Auto Cord Rewind Button
To rewind the power cord, press the rewind button with
one hand and guide the cable with the other hand to
ensure that it does not whip causing damage.
3. Power Control Button
Turn on the main switch on the vacuum machine, then
the power neon-light will be turn on. Then it is ready
for work. You can slide the power control button on
the handle to switch off or adjust the suction power
of the machine. If you stop the cleaning for a while,
please just slide the power control button on handle
to 'OFF', then the vacuum will stop to sucking. When
you fi nish all cleaning work, please again push the
main 'ON/OFF' switch on vacuum body, to switch off
the electricity supply to this vacuum. (The neon-light
will be turn off at that time.), and storage your vacuum
properly.
( Attention: The fl exible hose must be fi xed into the
vacuum body, then the vacuum can work. Otherwise,
the vacuum can't work without the fl exible hose fi xed
in.)

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

98292800

Table des Matières