Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Chapter 8 : REMOTE CONTROL PROGRAMMER'S GUIDE (continued)
8-4. COMMANDS AND RESPONSES TABLE
The following table resumes commands that are recognized as valid and the responses that will be returned to the control
device (on RS-232 port).
ASCII
RESPONSE
COMMAND
FRONT PANEL COMMANDS
C
CH
c
ch
o
OBLK
G
TAKE
Z
FRZ
INPUT COMMANDS
PC
PCH
PE
PEN
PL
PLD
PR
PRGB
PI
PSTD
PP
PPRC
OUTPUT COMMANDS
F
OFMT
fm
OSYN
fs
SCRN
p
OPAT
SWITCHING COMMANDS
XR
REFR
XA
REFA
XI
REFI
NOTE:
Rd/Wr = Read and write command.
PAGE 24
COMMAND
DESCRIPTION
Selected input.
Input selection.
Black screen selection.
Transition status.
FREEZE.
Input selection for adjustment.
Input disabling (according to PCH).
H sync load selection (according PCH) Rd/Wr
Input signal type selection. (according
to PCH).
Input standard selection (according to
PCH).
VCR mode (according to PCH).
Output format selection.
Output sync selection.
Type of screen selection
Test pattern.
Input "reference" selection.
Reference input.
NOTE: REFA can be different from
REFR, if no sync is connect to the
corresponding input.
Aspect ratio of the reference input.
TYPE
MIN MAX
1
4
Rd
1 = INPUT #1
3 = INPUT #3
Rd/Wr
1
4
1 = black screen
Rd/Wr
0
1
1 = transition in process (automatic reset at the
Rd
0
1
end of the effect transition).
0 = inactive
Rd/Wr
0
1
0 = All inputs
Rd/Wr
0
4
2 = INPUT #2
4 = INPUT #4
0 = Input disable
Rd/Wr
0
1
0 = Hi-Z load
0
1
0 = SDTV Composite
2 = SDTV YUV
Rd/Wr
0
9
4 = SDTV RGsB
6 = Computer (SOG)
8 = HDTV
0 = NTSC / PAL / SECAM
1 = NTSC
Rd/Wr
0
6
3 = NTSC 4.43 60Hz
5 = SECAM
0 = OFF
Rd/Wr
0
1
internal rate
0 = VGA 60 Hz
1 = SVGA 60 Hz
2 = XGA 60 Hz
3 = SXGA 60 Hz
4 = SXGA+ 60Hz
Rd/Wr
0
12
5 = VGA 75 Hz
6 = SVGA 75 Hz
7 = XGA 75 Hz
8 = SXGA 75 Hz
9 = D-ILA 4/3
10 = D-ILA 16/9
11 = HDTV 480p
12 = HDTV 720p
0 = H &V
Rd/Wr
0
2
2 = SOG (Sync On Green).
0 = screen 4/3
Rd/Wr
0
1
0 = no pattern
Rd/Wr
0
2
2 = color bar
Rd/Wr
0
4
0 = internal rate
1 = INPUT #1
2 = INPUT #2.
Rd
0
4
3 = INPUT #3.
4 = INPUT #4.
Rd/Wr
0
2
0 = 4/3
Rd = Read only command.
OCTO-QUATTRO™
VALUE
DESCRIPTION
2 = INPUT #2
4 = INPUT #4
1 = active.
1 = INPUT #1
3 = INPUT #3
1 = Input enable
1 = 75Ω load
1 = SDTV S.VIDEO
3 = SDTV RGBS TTL
5 = SDTV RGBS ana.
7 = Computer H&V/C
9 = Audio only
2 = PAL
4 = PAL 4.43 60 Hz
6 = Black & White
1 = ON
If fast switching =
input # X
0 = 640x480L
1 = 800x600L
2 = 1024x768L
3 = 1280x1024L
4 = 1400 x1050 L.
5 = 640x480L
6 = 800x600L
7 = 1024x768L
8 = 1280x1024L
9 = 1365x1024L
10 = 1365x768L
11 = HDTV 480p
12 = HDTV 720p.
1 = Composite
1 = screen 16/9
1 = centering
2 = 16/9
Publicité
Table des Matières
