Service Information; Storage; Electrical Connection; Disposal And Recycling - Parkside PTKS 2000 F4 Traduction Des Instructions D'origine

15.4.4 Fitting the saw blade (fig. 29)
1. Clean the outer and inner saw blade flange (6d/6c) care-
fully, before fitting a new saw blade (6).
2. Place a new saw blade (6) on the drive shaft (6e). Ob-
serve the rotational direction: The cutting angle of the teeth
must point in the running direction (forwards). The running
direction is usually also marked on the saw blade.
3. Fit the outer saw blade flange (6d) back on the drive shaft
(6e). Ensure the correct alignment of the outer saw blade
flange (6d).
4. Screw the fixing nut (6f) tight onto the drive shaft (6e) with
the hand.
5. Carefully turn the saw blade (6) in the running direction: It
must be precisely centred and must not "wobble". Check
that the saw blade (6) and outer saw blade flange (6d)
are sitting correctly and align the parts once more, if the
saw blade is not precisely centred.
m WARNING
Warning against unexpected hazards and damages to the
product
- Check the setting of the saw blade after every saw
blade replacement.
6. Hold the outer saw blade flange (6d) in position with the
open-ended spanner 22 mm (6a) and turn the fixing nut
(6f) tight in a clockwise direction with the open-ended
spanner 22 mm (6b).
7. Mount the table inlay (7) and the saw blade guard (4)
(see 9.3.3 and 9.5.1).
8. Check the correct setting of the riving knife (see 9.3.2).

15.5 Service information

With this product, it is necessary to note that the following parts
are subject to natural or usage-related wear, or that the follow-
ing parts are required as consumables.
Wearing parts*:Carbon brushes, table inlay, push stick, saw
blade
* may not be included in the scope of supply!

16. Storage

m WARNING
Danger of injury due to unexpected start-up of the machine
- Pull the mains plug out of the outlet.
ATTENTION
Product damage due to incorrect storage
- Store the product protected against dirt, dust and mois-
ture.
- Store the product in its original packaging.
1. Store the product in a dark, dry and frost-free place that is
inaccessible to unauthorised persons.
2. The optimum storage temperature lies between 5 and
30 °C.
3. Store the operating manual with the product.

17. Electrical connection

The electrical motor installed is connected and
ready for operation. The connection complies with
the applicable VDE and DIN provisions. The cus-
tomer's mains connection as well as the extension
cables used must also comply with these regula-
tions.
17.1 Damaged electrical connection cable
The insulation on electrical connection cables is often dam-
aged.
This may have the following causes:
• Pressure points, where connection cables are passed through
windows or doors
• Kinks where the connection cable has been improperly fas-
tened or routed
• Places where the connection cables have been cut due to
being driven over
• Insulation damage due to being ripped out of the wall outlet
• Cracks due to the insulation ageing
Such damaged electrical connection cables must not be used
and are life-threatening due to the insulation damage.
Check the electrical connection cables for damage regularly.
Ensure that the connection cables are disconnected from elec-
trical power when checking for damage.
Electrical connection cables must comply with the applicable
VDE and DIN provisions. Only use connection cables of the
same designation.
The printing of the type designation on the connection cable
is mandatory.
Connections and repair work on the electrical equipment may
only be carried out by electricians.
17.2 AC motor
• The mains voltage must be 220–240 V∼.
• Extension cables up to 25 m long must have a cross-section
of 1.5 mm².
• Extension cables over 25 m long must have a cross-section
of 2.5 mm².
Connections and repair work on the electrical equipment may
only be carried out by electricians.
Please provide the following information in the event of any
enquiries:
• Type of current for the motor
• Data of machine type plate
• Data of motor type plate

18. Disposal and recycling

The product is supplied in packaging to avoid transport dam-
age. This packaging is raw material and can thus be used
again or can be reintegrated into the raw material cycle.
The product is made of different materials, such as metals and
plastics. Take defective components to special waste disposal
sites. Check with your specialist dealer or municipal adminis-
tration!
77
GB