Error Messages; Cleaning The Touch Display - PIONEER DJ CDJ-TOUR1 Mode D'emploi

Problem
When buttons are pressed to call out
the hot cue storing mode or to reloop,
or when the lever is moved to set
reverse playback, the operation does
not start immediately.
The playing address display is not
displayed in the remaining time mode.
Much time is required for reading
storage devices (SD, USB) (flash
memory devices or hard disks).
Library browsing is not possible.
[HISTORY] is not displayed.
Nothing is displayed.
The scale is not displayed.
PRO DJ LINK does not work well.
There is no response when you touch
the lower screen, or the response
is bad. A position different from the
actually touched location responds.

Error messages

When this unit cannot operate normally, an error code appears on the display. Check the table below and take the measures indicated. If an error code
not shown on the table below is displayed, or if the same error code is displayed again after taking the indicated action, contact your store of purchase.
Error code Error type
E-7201 CANNOT READ DISC
E-8301 CANNOT READ DISC
E-8302 CANNOT PLAY TRACK(****)
E-8304
UNSUPPORTED FILE FORMAT
E-8305
E-9101 MECHANICAL TIMEOUT

Cleaning the touch display

Do not use organic solvents, acids or alkalis for cleaning the surface
of the touch display. Wipe with a dry soft cloth or a cloth immersed in
neutral detergent and squeezed properly.
Check
Is the quantize function on?
—
Is there a large number of folders or files stored on
the storage device (SD, USB)?
Are files other than music files saved on the stor-
age device (SD, USB)?
Is a medium on which library information is
recorded loaded?
Is the storage device (SD, USB) connected?
Is the auto standby function activated?
Is the track over 15 minutes long?
Are the player numbers properly set?
Is the LAN cable properly connected?
Is the switching hub's power turned on?
Is an unnecessary device connected to the switch-
ing hub?
Is it connected by USB cable?
Calibration adjustment of touch display is
deviating.
Description of error
TOC data cannot be read.
Disc that cannot be played normally is loaded.
Track data (file) on the disc or storage device
(SD, USB) cannot be read properly.
Music files that cannot be played normally
are loaded.
Mechanical error (time out) during loading or
ejecting of disc.
Remedy
When the quantize function is on, the operation starts from the nearest beat
position from where buttons are pressed or the lever is moved. To start the
operation immediately when buttons are pressed or the lever is moved, turn the
quantize function off.
When playing files recorded in VBR, it may happen that the set cannot detect the
length of the track immediately and that some time is required for the playing
address display to appear.
When there are many folders or files, some time may be required for loading.
When files other than music files are stored in folders, time is required to read
them as well. Do not store files or folders other than music files on the USB
device.
The library browse mode is only set when media on which library information
is recorded are loaded. When a medium on which no library information is
recorded is loaded, the folder browse mode is set.
The [HISTORY] function can only be used on the DJ player to which the storage
device (SD, USB) is connected.
This unit is shipped with the auto standby function turned on. If you do not want
to use the auto standby function, set [AUTO STANDBY] to [OFF].
The scale is not displayed for tracks whose playing time is over 15 minutes.
Set [PLAYER No.] to [AUTO] or to a number different from the number currently
set.
Connect the LAN cable properly to the [LINK] terminal.
Turn the switching hub's power on.
Disconnect the unnecessary device from the switching hub.
For a USB connection, install the USB (LINK Export) connections driver
software.
Adjust the touch display by using the [TOUCH DISPLAY CALIBRATION] settings
in the [UTILITY] screen (lower screen).
Cause and action
! Disc is cracked.dReplace the disc.
!
Disc is dirty.dClean the disc.
! If operation is normal with other discs, the problem is with that
disc.
! The track data (file) may be corrupt. dCheck whether the track
(file) can be played on another player, etc., capable of playing
the same formats as this unit.
Format is wrong.dReplace with music files in the proper format.
Displayed when mechanism operation is not completed within the
specified time.
9
En