Flotec FP0S1300X Série Notice D'utilisation page 3

English
Performance
GPH (LPH) at total feet (m)
3' 5'
10'
(3.05)
(0.91) (1.52)
975 gal 915 gal 700 gal
(3 690 L) (3 460 L) (2 650 L)
3'(0.91) 5'(1.52) 10'(3.05)
1140 gal 1050 gal 840 gal
(4 315 L) (3 975 L) (3 180 L)
1320 gal 1250 gal 930 gal
(4 996 L) (4 731 L) (3 520 L)
1600 gal 1524 gal 1260 gal
(6 056 L) (5 768 L) (4 769 L)
Installation
Risk of electric shock. Can shock, burn or
kill.Do not use power cord to lift motor. Always use handle.
1. Pump should be located and should rest on level
solid foundation. Do not suspend pump by means of
discharge pipe or power cord. Keep pump inlet screen
clear.
2. Thread outlet pipe into pump body carefully to avoid
stripping or crossing threads.
a. To install with garden hose, install adapter provided
with pump.
NOTICE To keep friction as low as possible, hose must
be 3/4" or larger. Keep hose as short as possible.
b. To install with rigid pipe, use plastic pipe. Wrap
thread with pipe thread sealant tape. Screw pipe
into pump hand tight +1 - 1-1/2 turns.
3. Power Supply: Pump is designed for 115V., 60 HZ.
operation and requires an individual branch circuit
of 15 amperes or more capacity. It is supplied with a
3-wire cord set with grounding-type plug for use in a
3-wire, grounded outlet. 3 wire extension cord, of at
least 14 AWG (2mm2) size is suggested, with larger
sizes for runs over 25 ft (7M). For safety, pump should
always be electrically grounded to a suitable electrical
ground such as a grounded water pipe or a properly
grounded metallic raceway, or ground wire system.
Do not cut off the round grounding prong.
Risk of sudden starts. Can cause electrical
shock and personal injury.The pump motor is equipped
with automatic resetting thermal protector and may
restart unexpectedly. Protector tripping is indication of
motor overloading as a result of operating pump at low
heads (low discharge restriction), excessively high or low
voltage, inadequate wiring, incorrect motor connections,
or a defective motor or pump.
Operation
Risk of electric shock. Can shock, burn
or kill. Do not handle pump or pump motor with wet
hands or when standing on wet or damp surface, or in
water. Disconnect power from pump before handling,
servicing, or attempting to repair pump.
1. The pump must be standing in at least 1/2" (12.7mm)
of water before starting it (one inch (25.4 mm) is
better). The shaft seal is water lubricated and may be
damaged if pump runs dry.
For parts or assistance, call Flotec Customer Service at
15'(4.57) 16'(4.80) 20'(6.09)
FP0S1100X
265 gal 0 gal
-
(1 000 L) (0 L)
15'(4.57) 18'(5.49) 20'(6.09)
FP0S1250X
480 gal 0 gal
-
(1 817 L) (0 L)
FP0S1300X
660 gal 630 gal 0 gal
(2 498 L) (2 385 L) (0 L)
FP0S1600X
372 gal
924 gal 648 gal
(3 497 L) (2 452 L)
(1 408 L)
2. After starting, the pump will lower the water level to
3/16" (4.75 mm) before losing suction. It will not pick
up water less than 3/16" deep when running and will
not operate successfully if started in only 3/16" of water.
22'(6.70)
3. Do not leave pump unattended! If the pump has
been operating satisfactorily and the discharge stream
-
suddenly stops coming out of the hose, stop the pump
22'(6.70)
immediately; do not allow it to run dry. A mop or
squeegee will be needed to remove remaining water.
-
4. The motor is equipped with an automatically resetting
thermal overload protector. If the motor gets too hot,
the overload protector will stop the motor before it
-
is damaged. When the motor has cooled sufficiently,
the overload protector will reset itself and the motor
0 gal
(0 L)
will restart.
NOTICE If the overload protector stops the pump
repeatedly, disconnect the power from the pump and
check it to find the problem. Low voltage, long extension
cords, clogged impeller, too much back pressure in the
discharge hose (as when pumping through 50' (15 M)
of coiled hose), or running pump with no load, can all
cause excessive cycling and overheating.
5. For Model FP0S1300X, the water being pumped cools
the motor, allowing the pump to run continuously
at any depth of water above 3/16". However, if the
motor overload stops the pump, allow it to cool for
one hour before restarting. Motor will not restart
before the overload has cooled.
6. For Models FP0S1100X and FP0S1250X, do not try
to run the pump continuously when the water level
is below 4" (102mm) or about 1/3 of the way up
the motor casing, as it will overheat. If the motor
overheats and the overload stops the pump, allow it
to cool for one hour before restarting. Motor will not
restart before the overload has cooled.
Airlocks
When a pump airlocks, it runs but does not move any
water. An airlock will cause the pump to overheat and
fail. This pump has an anti-airlock hole in the bottom
of the pump body. If you suspect an airlock, unplug the
pump, clean out the anti-airlock hole with a paper clip
or piece of wire, and restart the pump.
NOTICE This hole allows the pump to start priming
within 15 seconds in as little as 1/2" of water. NEVER
restart pump in less than 1/2" of water. Leakage from
the anti-airlock hole is normal.
800-365-6832
3