Magura HS 33 Mode D'emploi page 26

m
aintenance
Push.the.hose.cover. ( 4 ) .upwards.
) .
Unscrew.the.screw.plug. .from.the.filler.hole.in.the.brake.cylinder.
( 5 )
) .
Screw.the.barbed.fitting.of.the.filling.syringe.
) .
tighten.to.a.torque.of.max. 4 n·m (35 lbf·in).
Unscrew.the.lower.clamping.screw.of.the.clamping.clip.on.the.brake.
) .
lever.
HS 11: Turn.the.brake.lever.so.it.is.pointing.vertically.upwards.
) .
HS 33: Turn.the.brake.lever.so.it.is.pointing.horizontally.forwards.or.
) .
[ ]
backwards. l5 .
HS 33: The.bleed.hole.is.located.above.the.hose.inlet.
Î Î
Tighten.the.clamping.screw.slightly.
) .
HS 11: Push.the.hose.cover. .away.from.the.brake.lever.
( 6 )
) .
HS 11: Unscrew.the.barbed.fitting.
) .
lever.until.3 turns.of.the.thread.can.be.seen.
HS 11: Unscrew.the.EBT.plug.
( 8 )
) .
HS 33: Unscrew.the.EBT.screw. (
) .
Insert.the.bleed.syringe. .tightly.into.the.bleed.hole.
( 3 )
) .
Press.MAGURA.Royal Blood slowly.out.of.the.filling.syringe.
) .
the.brake.system.–.tap.lightly.on.the.brake.cylinder.and.brake.lever.
during.this.process.
Flick.the.brake.lever.2–3.times.
) .
This.loosens.air.bubbles.and.they.rise.into.the.bleed.syringe.
Î
Î
[ ] [ ]
. l6 /. l7 .
Continue.the.process.until.you.cannot.see.any.more.air.bubbles.
) .
The.brake.system.has.been.bled.
Î
Î
26
[ ]
l3 .
.into.the.filler.hole.and.
( 2 )
[ ]
l3 .
[ ]
.
l4
[ ]
.
l4
( 7 ) .of.the.brake.hose.from.the.brake.
.from.the.bleed.hole. .
( 9 )
[ ]
) .from.the.bleed.hole. ( ) . .
10 11 l5
[ ] [ ]
/. .
l6 l7
.through.
( 2 )
( )
3
oil loss when removing the bleed syringe.
Have.a.clean.cloth.at.hand.
Î –
Block.the.top.hole.with.your.thumb.before.removing.the.syringe.
Î –
After.removal.quickly.place.a.finger.on.the.tip.of.the.syringe.
Î –
Pull.the.bleed.syringe.out.of.the.bleed.hole.
) .
HS 11: Push.the.EBT.plug. .firmly.into.the.bleed.hole.
( 8 )
) .
HS 11: Screw.the.barbed.fitting. (
) .
and.tighten.to.a.torque.of.max. 4 n·m (35 lbf·in).
HS 33: Screw.the.EBT.screw. ( 10
) .
tightening.torque.of.max. 0.5 n·m (4 lbf·in).
HS 33: The.EBT.screw.fits.flush.with.the.housing.
Î
Î
Unscrew.the.barbed.fitting.of.the.filling.syringe.
) .
[ ]
hole. .
l3
Screw.the.screw.plug. ( 4 ) .into.the.filler.hole.
) .
[
ing.torque.of.4 n·m (35 lbf·in).
l3
Thoroughly.clean.up.any.oil.residues.on.any.surfaces.–.particularly.on.
) .
brake.track.areas.and.brake.pads.
Pull.and.hold.brake.lever.
) .
Make.sure.that.all.connections.are.tight.
) .
HS 11: Push.the.hose.cover. .onto.the.brake.lever.
( 6 )
) .
Move.the.brake.lever.into.the.customary.position.and.secure.– see.
) .
,.page.20.
i
nstalling Brake lever
Set.the.pressure.point.– see.
s
) .
etting tHe pressure pOint
,.page.23.
wear
[ ]
. .
( 9 ) l4
7 ) .of.the.brake.hose.into.the.brake.lever.
) .into.the.bleed.hole. ( 11 ) .and.tighten.to.a.
[ ]
.
l5
.from.the.filler.
( 2 )
( 5 ) .and.tighten.to.a.tighten­
]
.
/
cOmpensating fOr pad