Product Description And Specifications - Bosch GKS 235 Professional Instructions D'emploi

OBJ_BUCH-329-005.book Page 8 Wednesday, January 18, 2017 1:58 PM
8 | English
 Do not operate the power tool stationary. It is not de-
signed for operation with a saw table.
 Do not use high speed steel (HSS) saw blades. Such saw
blades can easily break.
 Do not saw ferrous metals. Red hot chips can ignite the
dust extraction.
 When working with the machine, always hold it firmly
with both hands and provide for a secure stance. The
power tool is guided more secure with both hands.
 Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
 Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
 Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse
(ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should
be cut off and an appropriate plug fitted in its place by an
authorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Products sold in AUS and NZ only: Use a residual current
device (RCD) with a rated residual current of 30 mA or
less.
Product Description and
Specifications
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
Intended Use
The machine is intended for lengthways and crossways cut-
ting of wood with straight cutting lines as well as mitre cuts in
wood while resting firmly on the workpiece. With suitable saw
blades, thin-walled non-ferrous metals, e. g., profiles, can al-
so be sawed.
Working ferrous metals is not permitted.
Technical Data
Circular Saw
Article number
Rated power input
No-load speed
Rotational speed under load, max.
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Starting cycles generate brief voltage drops. Interference with other equipment/machines may occur in case of unfavourable mains system conditions.
Malfunctions are not to be expected for system impedances below 0.25 ohm.
1 609 92A 35V | (18.1.17)
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Blade guard
2 Lock-on button for On/Off switch
3 On/Off switch
4 Auxiliary handle (insulated gripping surface)
5 Spindle lock button
6 Scale for mitre angle
7 Wing bolt for bevel-angle preselection
8 Wing bolt for parallel guide
9 Cutting mark, 45°
10 Cutting mark, 0°
11 Parallel guide
12 Retracting blade guard
13 Lever for retracting blade guard
14 Base plate
15 Wing bolt for bevel-angle preselection
16 Chip ejector
17 Hex key
18 Clamping bolt with washer
19 Clamping flange
20 Saw blade*
21 Mounting flange
22 Saw spindle
23 Fastening screw for extraction adapter*
24 Extraction adapter*
25 Clamping lever for cutting-depth preselection
26 Cutting-depth scale
27 Set of screw clamps*
28 Guide rail*
29 Connection piece*
30 Vacuum hose*
31 Guide-rail adapter*
32 Handle (insulated gripping surface)
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
GKS 235
3 601 E7A 0..
W 2100
-1
min 5000
-1
min 3500
GKS 235
3 601 E7A 0..
2100
5000
3500
Bosch Power Tools