SMW Autoblok AN Manuel D'utilisation page 4

CARATERISTIQUES TECHNIQUES:
Diamètre du mandrin - Fixation dir. ISO-A
Course par mors (au rayon)
Course du coin
Traction maxi (3 mors)
Traction maxi (2 mors)
Force de serrage totale maxi (3 mors)
Force de serrage totale maxi (2 mors)
Vitesse maxi (2 et 3 mors)
Masse (fixation ACP; sans mors)
CARACTERISTICAS TECNICAS:
Diámetro plato
Carrera por garra (sobre el radio)
Carrera del manguito
Fuerza de tracciòn Máx (3 garras)
Fuerza de tracciòn Máx (2 garras)
Fuerza de cierre Máx (3 garras)
Fuerza de cierre Máx (2 garras)
Velocidad Máx (2 y 3 garras)
Masa (Fijació brida; sin garra)
TECHNISCHE MERKMALE:
Futter Durchmesser - Directaufnahme ISO-A
Hub pro Backe
Kolbenhub
max. Betätigungskraft (3-Backen)
max. Betätigungskraft (2-Backen)
max. Gesamt- Spannkraft (3-Backen)
max. Gesamt- Spannkraft (2-Backen)
max. Drehzahl (2u. 3-Backen)
Gewicht (Z-Aufnahme ohne Backen)
Actual gripping force diagrams
The diagrams refer to 3-jaw chucks. The max gripping force is the total,
acting on the 3 jaws, obtained by applying to the chuck the max. allowed
traction to the draw bar. The data refers to a chuck in good conditions,
using SMW-AUTOBLOK K05 grease.
4
ALD
Type
ALM
ALD
Tipo
ALM
ALD
Typ
ALM
ALD
Type
ALM
ALD
Type
ALM
TECHNICAL FEATURES:
Chuck size - DIRECT ISO-A Mounting
Jaw stroke (radius)
Wedge stroke
Max draw-pull ( 3 jaws)
Max draw-pull (2 jaws)
Max gripping force (3 jaws)
Max gripping force (2 jaws)
Max speed (2 and 3 jaws)
Mass (plain back, without top jaws)
CARATTERISTICHE TECNICHE:
ø Autocentrante - Attacco dir. ISO-A
Corsa per griffa (sul raggio)
Corsa del manicotto
Forza di trazione max (3 griffe)
Forza di trazione max (2 griffe)
Forza di serraggio max (3 griffe)
Forza di serraggio max (2 griffe)
Velocità massima (2 e 3 griffe)
Massa (Att. a flangia; senza morsetti)
Speed (r.p.m.)
- CLOSED CENTER - LONG STROKE - INCH (ALD)
or METRIC (ALM) SERRATED MASTER JAWS.
- SENZA PASSAGGIO BARRA - CORSA LUNGA-
DENTATURA IN POLLICI (ALD) o METRICA (ALM).
- OHNE DURHGANG - GROSSEM BACKENHUB -
GRUNDBACKEN MIT ZOLL (ALD) oder METRI-
SCHER (ALM) SPITZVERZAHNUNG .
- CENTRE FERME - COURSE LONGUE- MORS
AVEC STRIURES EN POUCES (ALD) ou METRI-
QUES (ALM).
- SIN PASO BARRA - CARRERA LARGA - DENTA
DO EN PULGADAS (ALD) ó MÉTRICO (ALM)
125-A4 165-A5 210-A6
mm 6 7
mm 15 17
kN 25 30
kN 17 20
kN 45 54
kN 30 36
rpm 6000 5200
Kg 5,5 9,5
125-A4 165-A5 210-A6
mm 6 7
mm 15 17
kN 25 30
kN 17 20
kN 45 54
kN 30 36
rpm 6000 5200
Kg 5,5 9,5
125-A4 165-A5 210-A6
mm 6 7
mm 15 17
kN 25 30
kN 17 20
kN 45 54
kN 30 36
rpm 6000 5200
Kg 5,5 9,5
The dynamic gripping forces have been measured using the standard soft
top jaws placed in the most external position, but not exceeding the outer
diameter of the chuck. Using larger and heavier jaws and/or in a more
external position, it is necessary to reduce the rotation speed.
250-A8 315-A8 400-A11
8,5 10 12
21 25 30
53 68 80
35 45 54
95 125 145
63 83 97
4500 3600 2800
19 32 56
250-A8 315-A8 400-A11
8,5 10 12
21 25 30
53 68 80
35 45 54
95 125 145
63 83 97
4500 3600 2800
19 32 56
250-A8 315-A8 400-A11
8,5 10 12
21 25 30
53 68 80
35 45 54
95 125 145
63 83 97
4500 3600 2800
19 32 56
Speed (r.p.m.)
13
33
100
67
180
120
2200
84
13
33
100
67
180
120
2200
84
13
33
100
67
180
120
2200
84