SMW Autoblok AN Manuel D'utilisation page 23

MOUNTING WITH OPEN CENTER CYLINDERS
R
FORWARD
Cylinder X
1
VNK [mm] [mm]
70/37 0
102/46 -8
130/52 -8
150/67 -5
170/77 -5
200/86 -6
225/95 -6
250/110 -6
320/127 9
R
FORWARD
Cylinder 70/37 102/46
X X X X
VNK
1 2 1 2
[mm] 0 22 -8 33 -8
Chuck Y Chuck
BH.. BB.. BH.. BB..
[mm]
130 BHD-BHM 24 210 BHM-BBM 33
140 BBD-BBM 24 250 BHM
165 BHD-BHM 26 250 BBM
175 BBD-BBM 26 315 BHM
210 BHD-BBD 33 315 BBM
250 BHD-BBD 37 400 BHD-BHM 42
315 BHD-BBD 39 450 BHD-BHM 42
Note: BH means BHD, BHM;
RC means RCD, RCM, RCC;
X
Chuck
2
22
BHD BHM
33
210
36 BBD BBM
33
250 BHD
33
BBD BBM
36
36
250 BHM
36
– 315 BHD
L
H+Y+X
=
2
130/52 150/67 170/77
X X X X X X
1 2 1 2 1 2
36 -5 33 -5 33 -6
Y Chuck Y Chuck Y
BHD BH/FC
[mm] [mm] [mm]
165 28
22 210 33
32 250 37
22 500 55 315 39
39 630 55 400 42
800 55 500 60
630 60
BH/FC means BHD/FC, BHM/FC;
Indirect mounting
direct mounting
h. Make the hydraulic connections as the above sketch.
i. Mount the bracket (P) to stop the rotation of the oil collector cylinder.
Y
IMPORTANT: Be sure that the drain hose is in a vertical position and has a
[mm]
continuous slope (without any bends) up to the hydraulic power unit.
NOTE: The bracket must not push the drain hose axially.
28 j. Push the cylinder piston (D) fully ahead.
k. Draw back the chuck wedge (E) (jaws closed). Remove the top jaws and the
plug (for BH-BB types remove the front cover also).
l. Position the chuck in front of the machine spindle and screw the nut (C) on the
32
(B) side of the draw tube (6) using the (F) wrench.
m.Position the chuck correctly (the face driver in line with its seat), then draw the
chuck on the adaptor (2) - or directly on the machine spindle - pulling with the
22
cylinder at low pressure.
n. Screw the fixing screws of the chuck.
34
o. Check the unit. If the jaws do not make a full stroke, cut the pressure, and
adjust using the wrench (F),tightening or loosening the (C) nut.
Indirect mounting
direct mounting
200/86 225/95 250/110
X X X X X X
1 2 1 2 1 2
36 -6 36 -6 36 9
Chuck Y Chuck Y Chuck
RC KNCSN KNCSN
[mm] [mm]
165 37
210 43 140 38 315
250 50 170 42 400
315 50 210 44 500
400 56 225 44 630
500 56 260 51
BB means BBD, BBM;
MOUNTING WITH FRONT REGULATION
a. Mount the cylinder adaptor (5) on the lathe
spindle.
b. In case of indirect mounting, mount the chuck
adaptor (2) on the lathe spindle.
In case of direct mounting, the chuck adaptor
(2) (of T thickness) is already mounted on the
chuck.
c. Calculate the (H) length (see sketch), adding
R+S+T, or just measure the distance between
the two adaptors (5) and (2).
d. Calculate the (L) length of the draw tube (6)
according to the following formula:
L = H+Y-X1: when fastening the draw tube
with G1 thread (all type of cylinders).
L = H+Y+X2: when fastening the draw tube
with G2 thread.
e. Cut the draw tube (6) according to the (L)
length and make the outer thread (B) to fit the
threaded ring nut (C) mounted on the rear of
the chuck.
f. Screw the G1/G2 side of the draw tube (6) into
the cylinder piston (D).
g. Mount the cylinder on its adaptor (5).
MOUNTING WITHOUT REGULATION
a. Mount the cylinder adaptor (5) on the lathe
spindle.
b. In case of indirect mounting, mount the
chuck adaptor (2) on the lathe spindle.
In case of direct mounting, the chuck adap-
tor (2) (of T thickness) is already mounted on
the chuck.
c. Calculate the (H) length (see sketch), adding
R+S+T, or just
between the two adaptors (5) and (2).
d. Calculate the (L) length of the draw tube (6)
according to the following formula:
L = H+Y-X1: when fastening the draw tube
with G1 thread (all type of cylinders).
L = H+Y+X2: when fastening the draw tube
with G2 thread.
e. Cut the draw tube (6) according to the (L)
length and make the outer thread (B) to fit the
threaded ring nut (C) mounted on the rear of
the chuck.
f. Screw the G1/G2 side of the draw tube (6)
into the cylinder piston (D).
g. Mount the cylinder on its adaptor (5).
h. Make the hydraulic connections as the above
sketch.
i. Mount the bracket (P) to stop the rotation of
320/127 the oil collector cylinder.
X X
IMPORTANT: Be sure that the drain hose is
1 2
in vertical position and has a continuous
–
slope (without any bends) up to the hydraulic
power unit.
Y
NOTE: The bracket must not push the drain
hose axially.
[mm]
j. Push the cylinder piston (D) fully ahead.
k. Draw back the chuck wedge (E) (jaws clo-
51
sed).
57
l. Position the chuck in front of the machine
70 spindle; rotate the spindle and fully screw the
draw tube (6) into the chuck nut (C).
70
m. Position the chuck correctly (the face driver in
line with its seat), then draw the chuck on the
adaptor (2), or directly on the machine spind-
le, pulling with the cylinder at low pressure.
n. Screw the fixing screws of the chuck.
measure the distance
23