Transport; Setting Up; Assembling The Commode; Assembling The Side Sections - Aquatec OCEAN Mode D'emploi

4

Transport

You can easily disassemble the commode into its com-
ponent parts (section 3.1) for transport.
For detailed instructions on how to dismantle the de-
vice, please refer to section 5.
5

Setting up

Important!
●
Before setting up, inspect all parts for dam-
age during transport.
● This section describes the assembly. Disas-
sembly is carried out in reverse order.
● During assembly, make sure the parts are
positioned correctly in relation to each other
(fig. 1).
5.1

Assembling the commode

5.1.1

Assembling the side sections

1. Take the enclosed clips (7, fig. 1) out of the bag.
2. Place the seat frame on one side.
Important!
● Push in the side section evenly and do not
jam it.
●
Fasten the side section at the same height
at the front and back.
3. Push the side section (1, fig. 3) with the guides for
the footrests (4, fig. 3) forwards onto the seat
frame (3, fig. 3).
4. Align the clip recesses (5, fig. 3) at the front and
back of the side section with a hole on the seat
frame (2, fig. 3).
5. Push the clips (6, fig. 3) from outside into the side
section until the two lugs (7, fig. 3) enclose the
seat frame tube (3, fig. 3).
Important!
The left and right side sections must be adjust-
ed to the same height.
6. Turn the seat frame around and fit the second side
section in the same way.
7. Place the seat frame with the fitted side sections
on to the casters.
EN
5.1.2

Fitting the backrest

1. Lock all four casters. To do this, push down the
red foot pedal for the casters.
Important!
When folded up, the armrests must face for-
ward.
2. Push the backrest (4, fig. 4) down into the seat
frame (5, fig. 4) until the collar (3, fig. 4) touches
the seat frame tube (6, fig. 4).
Important!
●
The round section of the curved washers
must touch the seat frame tube.
● Tighten the screws using the Allen key sup-
plied.
3. Push a washer (2, fig. 4) onto each screw (1,
fig. 4) and fasten the backrest with two screws on
either side.
5.1.3

Fitting the footrests

Important!
The procedure is the same for the right and the
left footrests.
1. Push the footrest (2, fig. 5) and the footplate (4,
fig. 5) inwards to the guide (7, fig. 5) on the front
of the side section (8, fig. 5) until the groove (1,
fig. 5) catches the pin on the clip (6, fig. 5). The
footrests can no longer be turned to the sides.
5.2 Fitting and removing the grip wheels
(optional)
Important!
●
When the grip wheels are fitted, the rear
casters must be locked.
● The procedure is the same for the right and
the left wheels.
●
The hubs and locking brakes for the grip
wheels must have been fitted.
1. Align all four casters to the front.
2. Lock all the casters.
3. Push the axle (4, fig. 6) on the grip wheel inwards.
(The grip rings must face outward.)
4. Push in the button (5, fig. 6) on the outside of the
axle.
This releases the locking balls (3, fig. 6) on the end of
the axle.
5. Slightly raise the commode.
6. Push the axle into the hub (2, fig. 6) and push on
the grip wheel (6, fig. 6) as far as it will go.
7. Release the button.
11