Pan Detector; Child Lock Function - ROSIERES RIS3BC Instructions Pour L'installation

EN
17
18
16
In order to select a plate on
these models, directly touch the
cursor slider (2).
SWITCHING ON THE DEVICE
1 Touch the On touch key
least one second. The touch control
will become active, a beep will be
heard and the indicators (3) will light
up displaying a "-". If any cooking
area is hot, the related indicator will
flash an H.
If you do not take any action in the
next 10 seconds the touch control will
switch off automatically.
When the touch control is activated,
you can disconnect it at any time by
touching the touch button
if it has been locked (lock function
activated). The touch button
always has priority to disconnect the
touch control.
ACTIVATING PLATES
Once the Touch Control is activated
with sensor (1), any plate can be
turned on by following these steps:
1 Slide the finger or touch in any
position of one of the cursors
"slider" (2). The zone has been
selected and simultaneuously the
power level will be set between 0
and 9. That power value will be
shown on the corresponding power
indicator and its decimal dot (4) will
keep light up during 10 seconds.
2 Use the cursor slider (2) to choose
a new cooking level between 0 and
9.
As long as the plate is selected, in
other words, with the decimal (4)
dot light up, its power level can be
modified.
8
15
TURNING OFF A PLATE
Using the touch slider key (2) lower
the power to level 0. The hotplate will
switch off.
When a hot plate is switched off an
H will appear in its power indicator
(1) for at
(3), if the glass surface of the related
cooking area is hot and there is a risk
of burns. When the temperature drops,
the indicator (3) switches off (if the hob
is disconnected), or otherwise a "-" will
light up if the hob is still connected.
TURNING ALL PLATES OFF
All plates can be simultaneously
disconnected by using the general on/
off sensor (1). All plate indicators (3)
will turn off. If the heating zone turned
(1), even off is hot, its indicator shows an H..
(1)

Pan detector

Induction cooking zones have a built-in
pan detector. This way, the plate will
stop working if there is no pan present
or if the pan is not suitable.
The power indicator (3) will show a
symbol to designate "there is no pan
" if, while the zone is on, no pan is
detected or the pan is not suitable
If a pan is taken off the zone while it
is running, the plate will automatically
stop supplying energy and it will
show the symbol for "there is no pan".
When a pan is once again placed
on the cooking zone, energy supply
will resume at the same power level
previously selected.
If a pan is taken off the zone while it
is running, the plate will automatically
stop supplying energy and it will
show the symbol for "there is no pan".
When a pan is once again placed
on the cooking zone, energy supply
will resume at the same power level
17
18
16
14
previously selected.
When finished, turn off the
cooking zone by using the touch
controls. Otherwise an undesired
operation could occur if a pan is
accidentally placed on the cooking
zone during the three minutes.
Avoid possible accidents!
Warning : Burn Hazard: don't
place or leave the pot/pan outside
the cooking zones and/or over the
Control panel.
Warning: The bottom surface
of the pot / pan must be flat and
must not show any damage or wear.

Child lock Function

With the Child lock Function, you can
block the other sensors, except for the
on/off sensor
undesired operations. This function is
useful as a childproof safety.
To activate this function, touch sensor
(6) for at least one second. Once
you have done so, the pilot (7) turns
on indicating that the control panel is
blocked. To deactivate the function,
simply touch sensor
If the on/off sensor
turn off the appliance while the Child
lock function is activated, it won't be
possible to turn the cooktop on again
until it unblocks.
Silencer of the beep
When the hob is on, if one presses the
touch key
key
seconds, the beep that accompanies
each action will be deactivated. The
time indicator (12) will display "OF".
Fig.2
17
18
16
(1), in order to avoid
(6) again.
(1) is used to
(11) and the locking touch
(6) simultaneously for three