Yamaha PLG100-VL Mode D'emploi page 35

<Soft Pedal> 43H
Cntrl# parameter Data Range
67 Soft Pedal 0...127 (0-63:Off, 64-127:On)
If the Part Parameter Rcv SOFT PEDAL = OFF, that Part will
not receive Soft Pedal Messages. When the SOFT PEDAL is
set "ON" the effect will take place from the next Key On sig-
nal. Messages will control the Filter Cutoff Frequency. De-
pending upon the Voice, the effect may or may not have an
effect.
<Harmonic Content> 47H
Cntrl# parameter Data Range
71 Harmonic Content 0...127 (0:-64, 64:+0, 127:+63)
Messages which adjust the resonance set for each. Based on a
standard of 64, these values will be added to or subtracted from
the Voice data. Depending on the Voice, the effective range
may be narrower.
<Release Time> 48H
Cntrl# parameter Data Range
72 Release Time 0...127 (0:-64, 64:+0, 127:+63)
Messages which adjust the envelope release time. Based on a
standard of 64, values will be added to or subtracted from the
Voice data. Depending on the Voice, the effective range may
be narrower.
<Attack Time> 49H
Cntrl# parameter Data Range
73 Attack Time 0...127 (0:-64, 64:+0, 127:+63)
Messages which adjust the envelope attack time. Based on a
standard of 64, values will be added to or subtracted from the
Voice data. Depending on the Voice, the effective range may
be narrower.
<Brightness> 4AH
Cntrl# parameter Data Range
74 Brightness 0...127 (0:-64, 64:+0, 127:+63)
Default:40H
Messages which adjust the filter cutoff frequency. Based on a
standard of 64, values will be added to or subtracted from the
Voice data. Depending on the Voice, the effective range may
be narrower.
<Data Increment / Decrement> 60H/61H
Cntrl# parameter Data Range
96 Increment 0...127
97 Decrement 0...127
The data byte is ignored.
RPN messages which increase or decrease the MSB value of
the parameter by 1.
<NRPN (Non-Registered Parameter Number)
LSB/MSB> 62H/63H
Cntrl# parameter Data Range
98 NRPN LSB 0...127
99 NRPN MSB 0...127
If the Part Parameter Rcv NRPN = OFF, that Part will not
receive NRPN Messages.
First send the NRPN MSB and NRPN LSB to specify the pa-
rameter which is to be controlled. Then use the Data Entry to
set the value of the specified parameter.
The following NRPN numbers can be received.
NRPN Data-entry
MSB LSB MSB parameter
01H 08H mmH Vibrato Rate
01H 09H mmH Vibrato Depth
01H 0AH mmH Vibrato Delay
The Rate, Depth, and Delay Time for the Vibrato is controlled.
01H 20H mmH Filter Cutoff Frequency
01H 21H mmH Filter Resonance
01H 22H mmH Filter EG Depth
The Cut-off frequency, Resonance, and Envelope Depth for
the Filter is controlled.
01H 30H mmH Bass
01H 31H mmH Treble
The Bass and Treble are controlled.
01H 63H mmH EG Attack Time
01H 64H mmH EG Decay Time
01H 66H mmH EG Release
The Attack time, Decay time, and Release time for the Enve-
lope are controlled. Based on a standard of 64, values will be
added to or subtracted from the Voice data. Depending on the
Voice, the effective range may be narrower.
<RPN (Registered Parameter Number) LSB/
MSB> 64H/65H
Cntrl# parameter Data Range
100 RPN LSB 0...127
101 RPN MSB 0...127
If the Part Parameter Rcv RPN = OFF, that Part will not re-
ceive RPN Messages.
In correspondence to the following parameters.
RPN Data-entry
LSB MSB MSB parameter
00H 00H mmH Pitch Bend Sensitivity mm:00H-18H (0-+24)
MIDI Data Format
Data Range
mm:00H-40H-7FH
(-64-0-+63)
mm:00H-40H-7FH
(-64-0-+63)
mm:00H-40H-7FH
(-64-0-+63)
mm:00H-40H-7FH
(-64-0-+63)
mm:00H-40H-7FH
(-64-0-+63)
mm:00H-40H-7FH
(-64-0-+63)
mm:00H-40H-7FH
(-64-0-+63)
mm:00H-40H-7FH
(-64-0-+63)
mm:00H-40H-7FH
(-64-0-+63)
mm:00H-40H-7FH
(-64-0-+63)
mm:00H-40H-7FH
(-64-0-+63)
Data Range
Default:02H
35