Balluff BOD 21M-LBI05-S4 Notice D'utilisation page 60

Capteurs optoélectroniques
Capteur de distance laser avec IO-Link et fonctions additionnelles
BOD 21M-LBI05-S4
Interface IO-Link (suite)
Paramètres spécifiques à l'appareil
Index Nom
(déc.)
0x0057 Operating
(87) Hours
0x00B4 SIO Output
(180) Type
0x00B5 SIO Output
(181) Function
0x00B6 Switch
(182) Counter
Settings
0x00B7 Switch
(183) Counter
State
0x00B8 Time Delay
(184) Function
Q1
(Broche 4)
0x00B9 Time Delay
(185) Function
Q2 (Pin 2)
0x00BA Debounce
(186) Time
14 français
Sous- Nom Format
index
(déc.) données
0x01 (1) Operating
Hours
0x02 (2) Operating
Hours
Individual
0x01 (1) Q1
0x02 (2) Q2/Iout
0x01 (1) Unused
0x02 (2) Iout
0x01 (1) Mode
0x02 (2) Limit
0x03 (3) Unused
0x04 (4) StartupDelay
0x01 (1) Status
0x02 (2) Counter
0x01 (1) Delay Function
Mode
0x02 (2) Delay Time 1
(On delay)
0x03 (3) Delay Time 2
(Off delay,
One shot)
0x01 (1) Delay Function
Mode
0x02 (2) Delay Time 1
(On delay)
0x03 (3) Delay Time 2
(Off delay,
One shot)
0x01 (1) Pin 4
0x02 (2) Pin 2
Accès Plage de valeurs
de
UINT32 R
UINT8 R/W 0x01 (1) = PNP
0x02 (2) = NPN
0x03 (3) = PushPull
0x01 (1) = PNP
0x02 (2) = NPN
0x03 (3) = PushPull
0x05 (5) = Analog Output
4...20 mA
UINT8 R/W 0x00 (0)
0x00 (0) = Rising
Characteristics
0x01 (1) = Falling
Characteristics
UINT8 R/W 0x00 (0) = Off
0x01 (1) = Counter Static
0x02 (2) = Counter Auto
UINT16 0x0001...0xFFFF (1...65535)
UINT16 0
UINT8 0x00...0xFF (0...255)
UINT8 R Bit 0 = Count Limit OK
Bit 1 = Count Limit Too Low
Bit 2 = Count Limit Too High
UINT16
UINT8 R/W 0x00 (0) = Delay
0x01 (1) = One shot
UINT16 R/W 0x0000...0xFFFF (0...65535)
0 = Timing Function off
UINT16 R/W 0x0000...0xFFFF (0...65535)
0 = Timing Function off
UINT8 R/W 0x00 (0) = Delay
0x01 (1) = One shot
UINT16 R/W 0x0000...0xFFFF (0...65535)
0 = Timing Function off
UINT16 R/W 0x0000...0xFFFF (0...65535)
0 = Timing Function off
UINT16 R/W 0 = Timing Function off
0x0000...0xFFFF (0...65535)
0 = Timing Function off
Remarque
Compteur
d'heures de
service (heures)
Peut être remis à
zéro via la
commande
système Reset
Operating Hours
En mode SIO
En mode SIO
Secondes
Millisecondes
Millisecondes
Millisecondes
Millisecondes
Temps de
stabilisation
entrée Reset
(millisecondes)