Hoshizaki KMD-201AA Notice D'utilisation page 4

* The non-rewirable plug must never be used without a fuse cover
being fitted.
The correct replacement for the detachable fuse cover is identifiable
from the manufacturer's reference number stamped on the plug.
Supply of replacement fuse covers can be obtained from Hoshizaki
Parts/Service Centres.
Fuses should be rated at 10A and approved to BS 1362.
6. WATER SUPPLY AND DRAIN CONNECTIONS
Only potable water should be used for this icemaker.
* The connections to the mains water supply must be made in
accordance with the countries' current requirements of the Water
Supply or Water Fittings Regulations.
* To avoid performance reduction or malfunction caused by scaling,
the water supply should have a hardness of not more than 50
mg/L and a silica content of not more than 30 mg/L. Otherwise,
installation of a proper water treatment device will be required.
* Water supply pressure should be minimum 0.07 MPa (0.7 bar) and
maximum 0.78 MPa (8 bar). If the pressure exceeds 0.78 MPa
(8 bar), use a pressure reducing valve. Do NOT throttle back the
supply tap.
* A plumbing permit and services of a licensed plumber may be
required in some areas.
* Water should drain into an open trap.
* The icemaker drain is gravity flow, so ensure drain pipe has an
adequate pitch or fall.
* A vented tee connection is required for proper drain flow. See Fig. 6.
* The icemaker drain line must be run separately from the storage
bin/dispenser unit drain line. See Fig. 6.
* There should be no backflow in the water circuit.
* Water supply connection is intended to be made by means of a
pipe, not a hose set.
Note: Jointing compounds should be approved and suitable for
potable water use.
Icemaker
Water Supply Inlet
Icemaker
1/2"FPT
Icemaker
Drain Outlet
3/4"FPT
Bin
WARNING
Icemaker
Water Supply Line
Shut-Off Valve
Icemaker
Water Supply Line
Drain Valve
Bin Drain Outlet
3/4"FPT
Separate piping to approved
drain. Leave a two-inch (5cm)
vertical air gap between the
end of each pipe and the drain.
two-inch (5cm)
air gap
Floor
Drain
Fig. 6
II. OPERATING INSTRUCTIONS
1. This icemaker is designed to produce edible ice. To keep the
icemaker hygienic:
* Wash your hands before removing ice. Use the plastic
scoop provided (accessory).
* The storage bin is for ice use only. Do not store anything
else in the bin.
* Clean the storage bin before use (see "III. 1. CLEANING").
* Keep the scoop clean. Clean it by using a neutral cleaner
and rinse thoroughly.
* Close the door after removing ice to prevent entrance of
dirt, dust or insects into the storage bin.
2. The use of any electrical equipment involves the observance
of some fundamental rules. In particular:
* Instances of high humidity and moisture increase the risk
of electrical short circuits and potential electrical shocks. If
in doubt, disconnect the icemaker.
* Do not pull the power cord in order to disconnect the
icemaker from the feed network.
* This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their
safety.
* Young children should be supervised to ensure that they do
not play with the appliance.
3. All parts are factory-adjusted. Improper adjustments may
result in failure.
4. If the unit is turned off, wait for at least 3 minutes before
r e s t a r t i n g t h e i c e m a k e r t o p r e v e n t d a m a g e t o t h e
compressor.
1. OPERATION
The installer will normally commission the icemaker to start the
automatic icemaking process. To ensure continuous operation, make
sure that:
* The water supply tap is on,
* The icemaker is plugged into the power supply, and
* The control switch is in the "ICE" position.
2. PREPARING THE ICEMAKER FOR LONG STORAGE
1) Move the control switch to the "OFF" position.
2) Unplug the icemaker or disconnect the power supply.
3) Close the water supply line shut-off valve.
4) Remove all ice from the storage bin/dispenser, and clean the bin/
dispenser.
5) Ask for draining of the icemaker by professional qualified
personnel.
III. MAINTENANCE
1. CLEANING
1. Before carrying out any cleaning or maintenance operations,
unplug the icemaker from the electrical supply network.
2. Ask a trained service person to clean and sanitise the
icemaker water system at least twice a year and to check
and clean the condenser at least once a year.
3. This appliance must not be cleaned by use of a water jet.
3
ENGLISH
WARNING
WARNING