Maintenance And Cleaning; Transport; Obsah Dodávky; Zakres Dostawy - ATIKA FC 40-255 Notice Originale

If grass, scrub or other objects entangle in the cutting
tool or if the device vibrates abnormally, immediately stop
the engine and check the machine.
− The cutting thread is after-running once the lawn trimmer
has been cut off. Therefore wait until the thread is
stationary before you restart the product.
− Replace the cutting thread by an original spare part if it is
worn or damaged.

Maintenance and cleaning

Before each maintenance and cleaning work
− Switch off device.
− Wait until the cutting device does not longer
move.
− Remove the battery.
Wear protective gloves during maintenance and
cleaning work in the area of the cutting tool to
avoid possible injuries.
Maintenance and repair work other than those described in this
chapter is only allowed to be carried out by service staff.
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
Only use genuine spare parts. Other than genuine parts may
result in unpredictable damages and injury.
Maintenance
The cutting tool will not come to a standstill immediately after
•
cut-off. Before starting any service work wait until all parts
are stationary.
To guarantee a long and reliable usage of the product carry out
the following maintainance works regularly.
Check the device for obvious defects such as
loose fastening elements
−
worn or damaged components
−
bent, broken or damaged cutting tool
−
Necessary repair works or maintainance have to be carried
out before using the machine.
Cutting blade
Safe and efficient working is only possible with a
correctly sharpened and intact cutting blade.
Therefore, check the cutting blade for dull edges, bents, cracks
or other damages on a regular basis.
Have dull cutting blades sharpened by a specialist/service
workshop.

Both sides of the cutting blade may be used. Turn round
the cutting blade once and continue to work with the brush
cutter until both sides of the cutting blade are dull-edged.
Replace damaged cutting blade by new one.
24
Replacing the cutting thread
During cutting, the cutting threads wear or break off so that
grass can no longer be cut.
Pull out the damaged cutting thread and insert the new one
through the hole.

To ensure that the cutting threads are flexible in use and
last longer, they should absorb moisture before use.
Put cutting threads that were stored for a longer period or
purchased new in water for 1 - 2 days before use so that
they can absorb moisture.
Clean the machine thouroughly after each application so

that the faultless function is kept.
After work, remove grass, dirt, plant residues and moisture
•
(plant sap) with a brush or a damp cloth from the area of the
cutting tool and the guard.
Clean the case with a soft brush or a dry cloth.
•
Clean the contact plug (L) in the battery well with a soft
•
brush.
Do not clean the machine under running water or using a
•
high-pressure cleaner.
Do not use solvents (gasoline, alcohol, etc.) for plastic parts,
•
otherwise such parts may be damaged.
Keep the handles free of oil and grease.
•
Water, solvents and polishing agents shall not be
applied.
Make sure the ventilation slots are free from foreign objects
•
(risk of overheating).

For information on "Maintenance and cleaning" of the
battery and the charger, please refer to the respective
"Operating Instructions".

Transport

Before each transport
− Switch off device.
− Wait until the cutting device does not longer
move.
− Remove the battery.
Secure the cutting blade (10A) with the transport guard

(10B) against touching to avoid injuries or damages.
 Carry the device balanced on the shaft or hanging from the
carrying strap. Hold the cutting tool toward the back at this.
 When transporting the product within a car put it in the boot
or on a separate loading area.
 You may pull the device apart to save space.
 Do not throw the device when loading it. Secure the device
against tipping over or damages.
Check the device for damages if it was subjected to hard
jolts during transport.

For information on "Transport" of the battery and the
charger, please refer to the respective "Operating Instructions".
Cleaning