Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
S
w
i
t
c
h
i
n
g
o
f
f
S
w
i
t
c
h
i
n
g
o
f
f
Release the ON/OFF switch button (9).
The cutting thread is after-running once the lawn trimmer
has been powered off. Therefore wait until the thread is
stationary before you restart the product.
R
e
m
o
v
i
n
g
t
h
e
b
a
t
t
R
e
m
o
v
i
n
g
t
h
e
b
a
t
t
To remove the battery (7), press the battery release
button (20).
W
o
r
k
W
o
r
k
You may not start to operate the machine until you have
read these operating instructions, observed all the in-
structions given and installed the machine as described!
Observe all safety instructions in any case.
W
o
r
k
i
n
g
w
i
t
h
t
h
e
l
a
w
n
W
o
r
k
i
n
g
w
i
t
h
t
h
e
l
a
w
n
Correct working position
Before you start working it is recommended to adjust your lawn
trimmer so that you can work safely and comfortably.
Telescopic tube
The telescopic tube allows you to vary the working height.
1.
For this, slightly loosen the clamping nut (12) and adjust
the length.
2.
Then, retighten the clamping nut (12).
Guide handle
For better control, grasp the machine also at the front handle
(6).
You can adjust the front handle (6) to different work posi-
tions. For this, press both adjusting knobs of the handle
and move the handle to your desired work position.
A
d
j
u
s
t
i
n
g
t
h
e
c
u
t
t
i
n
g
h
A
d
j
u
s
t
i
n
g
t
h
e
c
u
t
t
i
n
g
h
The angle of the cutting head (2) can be adjusted to 4
different positions. For this, press the adjusting knob
(10) and turn the cutting head (2) to your desired posi-
tion.
Trimming
While trimming keep the lawn trimmer away from your body at a
sufficient distance. Tilt the product slightly forward and move it
from left to right.
It is recommended to cut higher grass above 15 cm in several
passes.
Guide the product around trees and shrubs so that the plants
are not damaged. Use the protective bow (3) for better control.
Caution! Damaged plants may die off.
Do not guide the cutting thread (22) directly at walls and paving
stones. Otherwise it will prematurely wear off.
19
e
r
y
e
r
y
i
n
s
t
r
u
c
t
i
o
n
s
i
n
s
t
r
u
c
t
i
o
n
s
t
r
i
m
m
e
r
t
r
i
m
m
e
r
e
a
d
a
n
g
l
e
e
a
d
a
n
g
l
e
E
d
g
e
t
r
i
m
m
i
n
g
E
d
g
e
t
r
i
m
m
i
n
g
To trim along edges and around shrubs and trees you have
to turn the cutting head (2) to the outermost position.
Remove the battery (7).
Loosen the clamping nut (14) and turn the upper part
(16) by 90° counterclockwisely.
Then, retighten the clamping nut (14).
Thread follow-up
During trimming, the cutting thread (22) wears (becomes
shorter) or it may tear off so that it can no longer cut grass.
The automatic thread follow-up releases 12 mm cutting
thread (22) when the motor has reached its speed. If you
need more than 12 mm cutting thread (22), turn the ma-
chine off. When the full speed is reached again, another 12
mm cutting thread (22) is released.
V
i
b
r
a
t
i
o
n
s
V
i
b
r
a
t
i
o
n
s
If persons who have blood circulation problems are too
often exposed to vibrations damages to the nervous system or
to blood vessels may occur.
You can reduce vibrations:
- by thick and warm working gloves,
- shorter working time (have longer breaks).
See a doctor if your fingers swell, you don't feel well or your
fingers become numb.
M
a
i
n
t
e
n
a
n
M
a
i
n
t
e
n
a
n
Before each maintenance and cleaning
work
− switch off device
− wait until the cutting thread is stationary.
− remove the battery
− wear protective gloves.
Maintenance and repair work other than those described in this
chapter is only allowed to be carried out by service staff.
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
Use only original parts. Other parts can result in unexpected
damages and injuries.
M
a
i
n
t
e
n
a
n
c
e
M
a
i
n
t
e
n
a
n
c
e
The cutting tool will not come to a standstill immediately after
cut-off. Before starting any service work wait until all parts are
stationary.
To guarantee a long and reliable usage of the product carry out
the following maintenance works regularly.
c
e
a
n
d
c
l
e
a
n
i
n
g
c
e
a
n
d
c
l
e
a
n
i
n
g
Publicité
Chapitres
Table des Matières
