stayer SC300W Instructions D'emploi page 44

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 71
3.Move horizontal angles indicator 14 until it marks
45º.
4.Check with an angle chart, that there are 45º
between the disk 16 and the stopper guide
8.
5.Repeat the same sequence for the horizontal
angle at -45º.
Adjusting
1.Loosen fastening the 4 screws 37.
2.Loosen and pull control 13 to move the head
horizontally until indicator 36 marks + 45º.
3.Move indicator 14 until the angle chart pattern
between the disk 16 and stopper guide 8 is
45º.
Adjusting the vertical mitre angle to 90º
IMAGES
A B C
Checking
1.Release vertical adjustment of the head by
loosening control element 28.
2.Move head to the right stop (90º) checking that
there is support at screw 30.
3.Lock the vertical adjustment of the head by
tightening control element 28.
4.Check the angle by means of a duly calibrated
a n g l e c h a r t o r a g o n i o m e t e r ( m i n i m u m
p r e c i s i o n + - 5 º ) a p p l y i n g o n e o f t h e
surfaces thereof on cutting table 15 and the
other on cutting disk 16.
5.Should the side of the angle chart not adjust
e x a c t l y t o t h e d i s k o r i f t h e d i r e c t
measurement of the goniometer reached a
deviation of more than +- 20º, proceed to
adjusting.
Adjusting
1.Release the vertical adjustment of the head by
loosening control element 28.
2.Move the head to the right stopper (90º).
3.Remove retainer nut of screw 30.
4.Place a goniometer (minimum precision +- 5º)
applying one of its sides on cutting table 15
and the other on cutting disk 16.
5.Act on adjusting screw 30 until obtaining a
measurement of 90º.
ENGLISH
43
6.Fasten the adjustment by tightening the retainer
nut of screw 30 whilst retaining screw 30
with a screwdriver so as to prevent it from
moving.
7.Block the vertical adjustment of the head by
tightening control element 28.
Adjusting the vertical mitre angle to 45º
IMAGES
A B
Checking
1.Release the vertical adjustment of the head by
loosening control element 28.
2.Move head to the left stop (45º).
3.Block the vertical adjustment of the head by
tightening the control element 28.
4.Check the vertical adjustment by means of a duly
c a l i b r a t e d a n g l e c h a r t o r a g o n i o m e t e r
(minimum precision +- 5º) applying one of
its sides on cutting table 15 and the other on
cutting disk 16.
5.Should the side of the angle chart not adjust
e x a c t l y t o t h e d i s k o r i f t h e d i r e c t
measurement of the goniometer reached a
deviation of more than +- 20º, proceed to
adjusting.
Adjusting
1.Release the vertical adjustment of the head by
loosening control element 28.
2.Move head to the left stop (45º).
3.Remove retainer nut of screw 27.
4.Check the vertical adjustment by means of a
g o n i o m e t e r ( m i n i m u m p r e c i s i o n + - 5 º )
applying one of its sides on cutting table 15
and the other on cutting disk 16.
5.Fix adjustment by tightening the retainer nut of
screw 27 whilst retaining screw 27 with a
screwdriver so as to prevent it from moving.
43

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Sc310wSc311wSce311wSc390wSc391wSll390w ... Afficher tout

Table des Matières