Day/Date/Am/Pm/Sun/Moon Models; Chronograph Models - Timex HIGHER-FUNCTION ANALOG Mode D'emploi

TO SET THE DATE
Instant date change:
1. Pull crown out one stop and turn CLOCKWISE until you reach correct date.
2. Push crown in to restart.

DAY/DATE/AM/PM/SUN/MOON MODELS

DAY
AM/PM
SUN/MOON
TO SET TIME:
1. PULL out crown to "C" position.
2. TURN crown clockwise to correct time. Day/am/pm/moon will also change.
3. Push in crown to "A" position.
NOTE: Remember to set time for am or pm (sun or moon).
TO SET DATE:
1. PULL out crown to "B" position.
2. TURN crown clockwise to correct date.
3. PUSH in crown to "A" position
TO SET DAY:
1. PULL out crown to "C" position.
2. Advance time 24 hours to change the day.
3. PUSH in crown to "A" position

CHRONOGRAPH MODELS

Review all chronographs to determine your watch type
TYPE 1
STOPWATCH
HOUR HAND
PUSHER "B"
SMALL
SECOND HAND
PUSHER "C"
STOPWATCH
SECOND HAND
• Crown position "A", "B" & "C"
• Pusher "A" (right) & "B" (left)
• Hour, minute and small second hands (6 o'clock eye) show time
• 12 o'clock eye shows "minutes elapsed" for chronograph
• 9 o'clock eye shows "hours elapsed" for chronograph
• The seconds sweep hand shows "seconds elapsed" for chronograph
DATE
NORMAL POSITION
A B C
CROWN
POSITION
PUSHER "A"
A B C
CROWN POSITION
NORMAL POSITION
STOPWATCH
1/20 SEC. HAND
TIME, CALENDAR, CHRONOGRAPH
This chronograph watch has three functions:
TIME
TO SET THE TIME:
1. PULL out Crown to "C" position
2. TURN Crown either way to correct time
3. PUSH in Crown to "A" position
CALENDAR
TO SET THE CALENDAR
1. PULL out Crown to "B" position
2. TURN Crown clockwise to correct position
3. PUSH in Crown to "A" position
CHRONOGRAPH
• The Chronograph is capable of measuring:
• Minutes elapsed up to 1 hour (12 o'clock eye)
• Hour elapsed up to 12 hours (9 o'clock eye)
• Seconds elapsed up to 1 minute (seconds sweep hand)
BEFORE USING THE CHRONOGRAPH:
Adjust all the chronograph hands to the "0" or 12 hr. position.
TO ADJUST THE CHRONOGRAPH HANDS:
1. PULL out CROWN to "C" position
2. PRESS pusher "A" intermittently until the seconds sweep hand resets to "0"
or 12-hr. position
3. PRESS pusher "B" intermittently until the hands in the 12 o'clock eye reset to
"0" or 12-hr position
4. PUSH in Crown to "A" position
NOTE: Make sure that the chronograph is stopped and reset before
adjusting.
NOTE: PRESSING and HOLDING either pusher "A" or "B" will cause the hands
to move continually until the pusher is released.
STANDARD CHRONOGRAPH MEASUREMENT:
1. PRESS pusher "A" to start timing
2. PRESS pusher "A" to stop timing
3. PRESS pusher "B" to reset
CHRONOGRAPH MODELS
TYPE 2
CHRONOGRAPH
MINUTE
CHRONOGRAPH
HOUR
HOUR
SMALL SECOND
SETTING THE TIME
1. PULL the crown out to the 2nd position "C".
2. Turn the crown to set hour and minute hands.
3. When the crown is pushed back to the normal position "A", small second
hand begins to run.
SETTING THE DATE
1. PULL the crown out to the 1st position "B".
2. Turn the crown counter-clockwise to set the date. *If the date is set between
the hours of around 9:00 PM and 1:00 AM, the date may not change on the
following day.
3. After the date has been set, push the crown back to the normal position "A".
3
ENGLISH
222-095001
CHRONOGRAPH
SECOND
PUSHER "A"
MINUTE HAND
CROWN
7
POSITION
B C
NORMAL POSITION "A"
PUSHER "B"
DATE