How To Start Your Watch; Water And Shock Resistance; Indiglo ® Night-Light; Analog/Digital Models - Timex HIGHER-FUNCTION ANALOG Mode D'emploi

Congratulations on purchasing your TIMEX
instructions carefully to understand how to operate your Timex timepiece.
Your watch may not have all of the features described in this booklet.
For more information, please visit:

HOW TO START YOUR WATCH

To start your watch remove the plastic guard from under the crown, then press
the crown in against the case. The second hand will begin advancing in one-
second intervals.
Some deep-depth water-resistant watches require the setting crown to be
screwed in to secure water-resistance. If your watch case has a protrusion with
screw threads, the crown must be screwed in after setting the watch.
To screw in, push the crown firmly against the threaded protrusion and hold
in while turning the crown clockwise. Continue to screw in the crown until it is
tight. You will need to unscrew the crown (counter-clockwise) before pulling it
out the next time you want to set your watch.

WATER AND SHOCK RESISTANCE

If your watch is water-resistant, meter marking (WR_M) is indicated.
Water-Resistance Depth
30m/98ft
50m/164ft
100m/328ft
200m/656ft
*pounds per square inch absolute
WARNING: TO MAINTAIN WATER-RESISTANCE, DO NOT PRESS ANY
BUTTONS OR PULL OUT THE CROWN UNDER WATER UNLESS YOUR
WATCH IS INDICATED AS 200 METER WATER-RESISTANT.
1. Watch is water-resistant only as long as crystal, crown and case remain
intact.
2. Watch is not a diver watch and should not be used for diving.
3. Rinse watch with fresh water after exposure to salt water.
4. Shock-resistance will be indicated on the watch face or caseback. Watches
are designed to pass ISO test for shock-resistance. However, care should be
taken to avoid damaging the crystal.
INDIGLO NIGHT-LIGHT
®
Press button or crown to activate light. Electroluminescent technology used in
the INDIGLO night-light illuminates entire watch face at night and in low light
®
conditions.

ANALOG/DIGITAL MODELS

4-PUSHER ANALOG/DIGITAL MODEL WITH INDIGLO
NIGHT-MODE FEATURE
®
PUSHER
PUSHER
"B"
PUSHER
PUSHER
"A"
watch. Please read these
®
Timex...com
p.s.i.a. * Water pressure Below Surface
60
86
160
284
NIGHT-LIGHT &
®
"C"
A B
CROW N
POSITION
PUSHER
"B"
"D"
PUSHER
"A "
TO USE INDIGLO
1. PRESS pusher "B" to illuminate the entire dial (Both analog and digital).
TO USE NIGHT-MODE
1. PRESS and HOLD pusher "B" for 3 seconds until you hear a beep.
2. Pressing any pusher will cause the INDIGLO
stay on for 3 seconds.
3. NIGHT-MODE
4. To deactivate NIGHT-MODE
seconds.
ANALOG TIME
TO SET ANALOG TIME
1. PULL the crown out to the "B" position.
2. TURN the crown either way to the correct time.
3. PUSH in the crown to the "A" position.
DIGITAL DISPLAY
1. The Digital display changes to each function every time you PRESS pusher
"A". (As illustrated below):
TIME / CALENDAR
DAILY ALARM
COUNTDOWN TIMER
CHRONOGRAPH
DUAL TIME
TO SET TIME / CALENDAR
1. PRESS pusher "A" to bring up TIME / CALENDAR display.
2. PRESS and HOLD pusher "D". HOLD will display until second flashes.
3. PRESS pusher "C" to reset to second to "00".
4. PRESS pusher "A" to let hour flash.
5. PRESS pusher "C" to advance hour.
6. PRESS pusher "A" and "C" as above to adjust tens of minutes, minute, year,
month, date, day and 12/24 hour format.
7. PRESS pusher "D" to complete setting.
8. View or select the TIME or CALENDAR to appear in your digital display.
• PRESS pusher "C" to view the CALENDAR for 2 seconds.
• PRESS and HOLD pusher "C" for 3 seconds until the watch beeps to
change the display to CALENDAR.
• To view or change the display to TIME, repeat the steps above.
NOTE: "A" or "P" will appear when the 12-Hour format is selected.
• Set this time to coordinate with the Analog time or another time zone.
• PRESS and HOLD pusher "C" for 2 seconds in setting mode, to activate fast
advance.
PUSHER
WILL
"C"
APPEAR
FOR 3
A B
SECONDS
CROW N
TO SET DAILY ALARM
POSITION
1. PRESS pusher "A" to bring up DAILY ALARM display: "ALARM" will appear
PUSHER
for 3 seconds followed by the current alarm setting time and time zone. The
"D"
1
NIGHT-LIGHT
®
FEATURE
®
feature will last for 3 hours.
®
feature PRESS and HOLD pusher "B" for 3
®
TIME/ DAILY
CALENDAR ALARM
START
Press and release MODE Press and release MODE
button once. button once.
DUAL TIME CHRONOGRAPH
HOUR MINUTE SECOND MONTH
FOLLOWED BY
THE CURRENT
ALARM SETTING
TIME AND TIME
ZONE.
ENGLISH
222-095001
night-light to illuminate and
®
COUNTDOW N
TIMER
Press and release MODE
button once.
DATE DAY
CALENDAR