DSC Power832 Manuel D'installation page 4

AVIS: L'étiquette de l'Industrie Canada identifie le matériel homologué. Cette
étiquette certifie que le matériel est conforme à certaines normes de protection,
d'exploitation et de sécurité des réseaux de télécommunications. Industrie Can-
ada n'assure toutefois pas que le matériel fonctionnera à la satisfaction de l'utili-
sateur.
Avant d'installer ce matériel, l'utilisateur doit s'assurer qu'il est permis de le rac-
corder aux installations de l'entreprise locale de télécommunication. Le matériel
doit également être installé en suivant une méthode acceptée de raccordement.
L'abonné ne doit pas oublier qu'il est possible que la conformité aux conditions
énoncées ci-dessus n'empêchent pas la dégradation du service dans certaines sit-
uations.
Les réparations de matériel homologué doivent être effectuées par un centre
d'entretien canadien autorisé désigné par le fournisseur. La compagnie de télé-
communications peut demander à l'utilisateur de débrancher un appareil à la
suite de réparations ou de modifications effectuées par l'utilisateur ou à cause de
mauvais fonctionnement.
Pour sa propre protection, l'utilisateur doit s'assurer que tous les fils de mise à la
terre de la source d'énergie électrique, les lignes téléphoniques et les canalisa-
tions d'eau métalliques, s'il y en a, sont raccordés ensemble. Cette précaution est
particulièrement importante dans les régions rurales.
AVERTISSEMENT: L'utilisateur ne doit pas tenter de faire ces raccordements
lui-même; il doit avoir recours à un service d'inspection des installations élec-
triques, ou à un électricien, selon le cas.
L'indice de charge (IC) assigné a chaque dispositif terminal indique, pour éviter
toute surcharge, le pourcentage de la charge totale qui peut être raccordée à un
circuit téléphonique bouclé utilisé par ce dispositif. La terminaison du circuit
bouclé peut être constituée de n'importe quelle combinaison de dispositifs,
pourvu que la somme des indices de charge de l'ensemble des dispositifs ne
dépasse pas 100.
L'Indice de charge de ce produit est 2.
FCC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not expressly approved by Digital Security
Controls Ltd. could void your authority to use this equipment.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential instal-
lation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be deter-
mined by turning the equipment off and on, the user is encouraged to try to cor-
rect the interference by one or more of the following measures:
• Re-orient the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.
The user may find the following booklet prepared by the FCC useful: "How to
Identify and Resolve Radio/Television Interference Problems". This booklet is
available from the U.S. Government Printing Office, Washington D.C. 20402,
Stock # 004-000-00345-4.
important information
This equipment complies with Part 68 of the FCC Rules. On the side of this
equipment is a label that contains, among other information, the FCC registra-
tion number of this equipment.
NOTIFICATION TO TELEPHONE COMPANY The customer shall notify the
telephone company of the particular line to which the connection will be made,
and provide the FCC registration number and the ringer equivalence of the pro-
tective circuit.
FCC Registration Number: F53CAN-32104-AL-E
Ringer Equivalence Number: 0.6B
USOC Jack: RJ-31X
TELEPHONE CONNECTION REQUIREMENTS Except for the telephone com-
pany provided ringers, all connections to the telephone network shall be made
through standard plugs and telephone company provided jacks, or equivalent,
in such a manner as to allow for easy, immediate disconnection of the terminal
equipment. Standard jacks shall be so arranged that, if the plug connected
NOTICE: The Industry Canada label identifies certified equipment. This certifi-
cation means that the equipment meets certain telecommunications network pro-
tective, operational and safety requirements. Industry Canada does not
guarantee the equipment will operate to the user's satisfaction.
Before installing this equipment, users should ensure that it is permissible to be
connected to the facilities of the local telecommunications company. The equip-
ment must also be installed using an acceptable method of connection. The cus-
tomer should be aware that compliance with the above conditions may not
prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian main-
tenance facility designated by the supplier. Any repairs or alterations made by
the user to this equipment, or equipment malfunctions, may give the telecommu-
nications company cause to request the user to disconnect the equipment.
User should ensure for their own protection that the electrical ground connec-
tions of the power utility, telephone lines and internal metallic water pipe sys-
tem, if present, are connected together. This precaution may be particularly
important in rural areas.
CAUTION: Users should not attempt to make such connections themselves, but
should contact the appropriate electric inspection authority, or electrician, as
appropriate.
The Load Number (LN) assigned to each terminal device denotes the percentage
of the total load to be connected to a telephone loop which is used by the device,
to prevent overloading. The termination on a loop may consist of any combina-
tion of devices subject only to the requirement that the total of the Load Numbers
of all the devices does not exceed 100.
The Load Number of this unit is 2.
thereto is withdrawn, no interference to the operation of the equipment at the
customer 's premises which remains connected to the telephone network shall
occur by reason of such withdrawal.
INCIDENCE OF HARM Should terminal equipment or protective circuitry cause
harm to the telephone network, the telephone company shall, where practicable,
notify the customer that temporary disconnection of service may be required;
however, where prior notice is not practicable, the telephone company may tem-
porarily discontinue service if such action is deemed reasonable in the circum-
stances. In the case of such temporary discontinuance, the telephone company
shall promptly notify the customer and will be given the opportunity to correct
the situation.
ADDITIONAL TELEPHONE COMPANY INFORMATION The security control
panel must be properly connected to the telephone line with a USOC RJ-31X tele-
phone jack.
The FCC prohibits customer-provided terminal equipment be connected to party
lines or to be used in conjunction with coin telephone service. Interconnect rules
may vary from state to state.
CHANGES IN TELEPHONE COMPANY EQUIPMENT OR FACILITIES The tele-
phone company may make changes in its communications facilities, equipment,
operations or procedures, where such actions are reasonably required and
proper in its business. Should any such changes render the customer's terminal
equipment incompatible with the telephone company facilities the customer
shall be given adequate notice to the effect modifications to maintain uninter-
rupted service.
RINGER EQUIVALENCE NUMBER (REN) The REN is useful to determine the
quantity of devices that you may connect to your telephone line and still have all
of those devices ring when your telephone number is called. In most, but not all
areas, the sum of the RENs of all devices connected to one line should not exceed
five (5.0). To be certain of the number of devices that you may connect to your
line, you may want to contact your local telephone company.
EQUIPMENT MAINTENANCE FACILITY If you experience trouble with this
telephone equipment, please contact the facility indicated below for information
on obtaining service or repairs. The telephone company may ask that you dis-
connect this equipment from the network until the problem has been corrected
or until you are sure that the equipment is not malfunctioning.
Digital Security Controls Ltd. 160 Washburn St., Lockport, NY 14094
iv