Tone Control Bypass 9C; Bass And Treble Controls 9C; Source Input Selector 8 J; Dimmer Control - Rotel RA‑1592 Manuel De L'utilisateur

NOTE: This setting is saved permanently including after powering off
the RA‑1592.
To make temporary changes not saved after power off, from the remote,
press the BAL C button to access the BALANCE SETTING menu, then press
the up/down/left/right G arrow buttons to adjust. When finished, press
the BAL C button again to exit the menu.

Tone Control Bypass 9C

Bass and Treble Control (Tone Control) circuits are bypassed at factory
default to ensure the purest possible sound. The front display will show TONE
BYPASS. To turn on the tone control from the front panel, press the MENU
button to toggle to the Bypass control then press the - or + buttons on
9
the front panel to turn bypass on or off.
NOTE: This setting is saved permanently including after powering off
the RA‑1592.
To temporarily changes the Tone Control Bypass, press the BYPASS
on the remote control to toggle the Bypass mode enabled and disabled.

Bass and Treble Controls 9C

Set the Bass or Treble controls from the front panel by pressing the MENU
9 button to toggle to the BASS / TREBLE menu. Press ENTER
toggle between the options. Press the - or +
The Bass and Treble values range from -10 to +10.
NOTE: These settings are saved permanently including after powering
off the RA‑1592.
To temporarily change the Bass and Treble settings from the remote control,
press the BASS or TREB button
arrow buttons on the remote to adjust the value.
NOTE: Bass and Treble changes are only available when Tone Bypass
is disabled (see Tone Control Bypass section).
A properly setup high-performance audio system produces the most natural
sound with little or no adjustment of the tone controls. Use these controls
sparingly. Be particularly careful when turning the controls up as this
increases the power output in the bass or treble range, increasing the load
on the amplifier and speakers.
NOTE: Setting the Bass and Treble controls does not automatically turn
on the tone control. To turn on tone control, refer to previous section
Tone Control Bypass.

Source Input Selector 8 J

Press the corresponding input button on the front panel
J to select the desired listening source.
Push the front panel source buttons to toggle between Optical 1 - 3, Coaxial
1- 3 and Aux or use the dedicated source button on the remote control.

Dimmer Control

Display Dimmer 9 B

To change the brightness of the front display, press the MENU
to toggle to the Display Settings. Then press the - or + buttons on the front
panel to change the brightness.
9
9 button to adjust the value.
C , then press the up/down/left/right
8 or remote control
NOTE: This setting is saved permanently including after powering off
the RA‑1592.
To temporarily change the display brightness, press the DIM
the remote.
PC‑USB Input q
Connect this input using the supplied USB cable to the USB socket of your
computer.
The RA-1592 supports both USB Audio Class 1.0 and USB Audio Class
2.0 modes. Windows computers do not require installation of a driver for
USB Audio Class 1.0 and support playback of audio up to 96kHz sampling
rates. The Factory Default setting is USB Audio Class 1.0.
To take advantage of USB Audio Class 2.0 audio playback supporting
C button up to 192kHz sampling rates you will need to install the Windows driver
supplied on the CD included with the RA-1592. You will also need to switch
the RA-1592 to USB Audio Class 2.0 playback mode with the following:
• Press MENU on the front panel until "PC-USB AUDIO CLASS" appears
button to on the display.
• Select "2.0" using the "-" button then press "ENTER".
• Power cycle the RA-1592 and reboot your PC after changing the USB
Audio mode to ensure both units are properly configured.
Many audio playback applications do not support 192kHz sampling rate.
G Please confirm your audio player supports 192kHz audio and you have
192kHz audio files to properly playback this sample rate. Also, you may
need to configure the audio driver in your PC to output 192kHz or your
computer may "down sample" to a lower audio sample rate. For more
information please refer to your audio player or operating system information.
NOTE: USB Audio Class 2.0 requires installation of the Windows PC
driver on the CD ROM included with the RA‑1592.
NOTE: MAC computers do not require a driver to support PC‑USB
1.0 or 2.0 audio.
NOTE: Upon successful installation of the driver, you may need to select
the ROTEL audio driver from the audio/speaker setup of your computer.
NOTE: The RA‑1592 supports both DSD and DOP audio playback
in 1X and 2X formats. Consult your audio player to confirm proper
operation for playback of these audio formats.

RS232 t

The RA-1592 can be controlled via RS232 for integration with automation
systems. The RS232 input accepts a standard straight DB-9 Male-to-Female
cable.
For additional information on the connections, software, and operating codes
9
button for RS232 control of the RA-1592, contact your authorized Rotel dealer.
13
B button on