Access To Menus; Parameter Menu - BFT DEIMOS BT UL Instructions D'utilisation Et D'installation

ACCESS TO MENUS

Press the OK key
OK
BFT
Control unit software version
qscd ul
OK
No. total manoeuvres
0000
(in hundreds)
0000
No. manoeuvres since latest
00
maintenance (in hundreds)
No. radio control devices
memorised
+ -
PArAM
OK
+/-
FINE
- +
+ -
LoGIc
OK
+/-
FINE
- +
FOLLOWING MENUS
FIG. B
8 8 8 8
[ 00 ]
Preset value
Parameter increment/reduction
/ON
/OFF or ON/OFF commutation
Press OK key (Enter/confirm)
OK
- + Menu scrolling
(+ = preceding - = following)
[ 010 ]
tcA OK
- +
[ 080 ]
OP. T
OK
- +
[ 080]
CLS. T
OK
- +
[ 050 ]
op. t slow
OK
- +
[ 050 ]
cls. t slow
OK
- +
[15. 0 ]
norm. op. speed
OK
- +
[15. 0 ]
norm. cls. speed
OK
- +
[ 0
slow speed
OK
- +
[
OK
Zone
[oFF]
OK
tcA
- +
[oFF]
3 step OK
- +
[oFF]
ibl open OK
- +
[oFF]
OK
photoc. open
- +
[oFF]
OK
tEst Phot
- +
[oFF]
OK
test bar
- +
[on ]
OK
fault phot
- +
[oFF]
OK
preal
- +
[oFF]
OK
hold to run
- +
[oFF]
OK
start close
- +
[oFF]
OK
fixed code
- +
[on ]
OK
radio prog
- +
[oFF]
OK
LooP
- +
[oFF]
OK
MAStEr
- +
[oFF]
OK
ice
www.BFTGateOpeners.com | (800) 878-7829
Fig. A
LEGENDA
+/-
Simultaneously press the + and - keys.
Simultaneous pressure of the + and – keys
allows you to exit the active menu and return
to the preceding menu; if this takes place at
OK the main menu level, programming is exited
and the display switched off.
The modifications made are only confirmed if
the OK key is subsequently pressed.
Message: Programming in progress
PRG
Message: KO! (value or function error)
Message: "Wait" (enter value or function)
OK PrG
PrG
OK
OK PrG
OK PrG
OK PrG
PrG
OK
OK PrG
]
OK PrG
0 ]
OK
PrG
ON
OK PrG
OFF
ON
OK PrG
OFF
ON
OK PrG
OFF
ON
OK PrG
OFF
ON
OK PrG
OFF
ON
PrG
OK
OFF
ON
OK PrG
OFF
ON
OK PrG
OFF
ON
PrG
OK
OFF
ON
OK PrG
OFF
ON
PrG
OK
OFF
ON
PrG
OK
OFF
ON
OK PrG
OFF
ON
PrG
OK
OFF
ON
PrG
OK
OFF

PARAMETER MENU

TCA (automatic closing time)
value expressed in seconds
(default 10=10s, min 3=3s, max
120=120s)
Opening Motor torque – value
expressed in % (default 80%, min 1%,
max 99%)
Closing Motor torque – value expressed
in % (default 80%, min 1%, max 99%)
Slow-down opening motor torque –
value expressed in % (default 50%, min
1%, max 99%)
Slow-down closing motor torque –
value expressed in % (default 50%, min
1%, max 99%)
Fast opening time
value expressed in seconds
(default 15=15s, min 1=1s, max 2=2 min)
Fast closing time
value expressed in seconds
(default 15=15s, min 1=1s, max 2=2 min)
Slow-down numerical value
(default 0, min 0, max 3)
Zone numerical value
(default min 0, max 127)
DEIMOS BT UL Ver. 08 -
19