Prior To Initial Operation; Know Your Product; Operation; Switching On - Switching Off - SPARKY HD Professional FK 3012 Notice Originale

this Manual and must be informed about its
potential hazards. Children and frail peo-
ple must not use this tool. Children should
be supervised at all times if they are in the
area in which the tool is being used. It is also
imperative that you observe the accident
prevention regulations in force in your area.
The same applies for general rules of occu-
pational health and safety.
▪ The manufacturer shall not be liable for any
changes made to the tool nor for any dam-
age resulting from such changes.
▪ The power tools must not be used outdoors
in rainy weather, or in moist environment (af-
ter rain) or in close vicinity with easily flam-
mable liquids and gases. The working place
should be well lit.

Know your product

Before using the power tool, familiarize your-
self with all the operating features and safety
requirements.
Use the tool and accessories only for the ap-
plications intended. All other applications are
expressly ruled out.
1. Wheel guard
2. Arm
3. Cutting depth scale
4. Screw for fixing the groove depth
5. Driving machine
6. End stop for fixing the operating
position of the driving machine
7. Screw for fixing the driving machine
8. Auxiliary handle
9. ON/OFF switch
10. Roller support
11. Flange
12. Diamond wheel
13. Spacer washer
14. Lock nut
15. Spindle lock button
16. Dust extraction pipe

Operation

This power tool is supplied from single-phase
alternating current mains only. It is double insu-
lated according to EN 60745-1 and IEC 60745
and can be connected to grounded or not
grounded sockets. This power tool is radio
suppressed in compliance with EMC Directive
2004/108/EC.
This power tool is designed for cutting grooves
with adjustable width and depth only in the
materials, specified on the wheels used with
8
EN
this tool (concrete, aerated concrete, masonry,
stone, etc., for laying electric installation, duct
and gas armature, cable networks, etc. The
machine is designed for dry cutting only.

PRIOR TO INITIAL OPERATION

▪ The machine may be delivered with the
wheel guard mounted at the factory. Ensure
that the wheel guard is mounted properly
and fixed reliably prior to the initial and any
following operation.
▪ The machine may be delivered with the
wheel mounted at the factory. Ensure that
the wheel is mounted properly and fixed reli-
ably prior to the initial and any following op-
eration.
▪ Make sure the power supply voltage corre-
sponds to the value indicated on the name
plate with technical data of the tool.
▪ Always check the position of ON/OFF switch.
The power tool must be connected and dis-
connected to the power supply socket only
when this switch is in OFF position. If the
plug is connected to a receptacle while the
power switch is in the ON position, the power
tool will start operating immediately, which
could cause a serious accident.
▪ Make sure that the cord and the plug are in
order. If the replacement of the supply cord
is necessary, this has to be done by the
manufacturer or his agent in order to avoid
a safety hazard.
WARNING: Always switch off and
unplug the power tool prior to any adjustment,
servicing or maintenance.
▪ In case the work area is remote from the
power source, use as short as practicable
extension cord with proper cross-section.
▪ Check that the auxiliary handle is properly
mounted and reliably tightened.
▪ Make sure the diamond wheels are reliably
fastened and rotate freely.

SWITCHING ON - SWITCHING OFF

▪ Switching on: Push the slider of ON/OFF
switch 9 forward until its front end will sag,
thus fixing itself.
▪ Switching off: Press the back, lifted end of
switch 9 and release it to return in its initial
position.

REPLACING THE WHEELS

Remove the plug from the socket before car-
rying out any operation on the machine. Use
FK 3012 ● FK 3014