Know Your Product; Operation; Prior To Initial Operation - SPARKY HD Professional FK 6522 Notice Originale

▪ Always switch off the machine prior to leaving
it down.
▪ Do not leave the switched off machine on
roller supports 7, always place it leaning on its
side.
▪ Carry the tool only by the auxiliary handle 5
and the body of the driving machine.
▪ Use genuine spare parts and accessories
only.
▪ The tool must be used only for its prescribed
purpose. Any use other than those mentioned
in this Manual will be considered a case of
misuse. The user and not the manufacturer
shall be liable for any damage or injury result-
ing from such cases of misuse.
▪ To use this tool properly, you must observe
the safety regulations, the assembly instruc-
tions and the operating instructions found in
this Manual. All persons who use and service
the machine have to be acquainted with this
Manual and must be informed about its poten-
tial hazards. Children and frail people must not
use this tool. Children should be supervised at
all times if they are in the area in which the
tool is being used. It is also imperative that
you observe the accident prevention regula-
tions in force in your area. The same applies
for general rules of occupational health and
safety.
▪ The manufacturer shall not be liable for any
changes made to the tool nor for any damage
resulting from such changes.
▪ The power tools must not be used outdoors in
rainy weather, or in moist environment (after
rain) or in close vicinity with easily flammable
liquids and gases. The working place should
be well lit.

Know your product

Before using the power tool, familiarize yourself
with all the operating features and safety re-
quirements.
Use the tool and accessories only for the appli-
cations intended. All other applications are ex-
pressly ruled out.
1. Driving machine
2. Wheel guard
3. Wheel guard cover
4. Dust extraction adapter
5. Auxiliary handle
6. Lever for adjusting the cutting depth
7. Roller support
8. ON/OFF switch locking button
8
EN
9. ON/OFF switch
10. Cutting depth scale
11. Flange
12. Driving diamond wheel
13. Spacer washer
14. Lock nut
15. Cutting marker
16. Spindle lock button
"L" Guiding line

Operation

This power tool is supplied from single-phase al-
ternating current mains only. It is double insulat-
ed according to EN 60745-1 and IEC 60745 and
can be connected to grounded or not grounded
sockets. This power tool is radio suppressed in
compliance with EMC Directive 2004/108/EC.
This power tool is designed for cutting grooves
with adjustable width and depth only in the mate-
rials, specified on the wheels used with this tool
(concrete, aerated concrete, masonry, stone,
etc., for laying electric installation, duct and gas
armature, cable networks, etc. The machine is
designed for dry cutting only.

PRIOR TO INITIAL OPERATION

▪ The machine may be delivered with the wheel
guard mounted at the factory. Ensure that the
wheel guard is mounted properly and fixed
reliably prior to the initial and any following
operation.
▪ The machine may be delivered with the wheel
mounted at the factory. Ensure that the wheel
is mounted properly and fixed reliably prior to
the initial and any following operation.
▪ Make sure the power supply voltage corre-
sponds to the value indicated on the name
plate with technical data of the tool.
▪ Always check the position of ON/OFF switch.
The power tool must be connected and dis-
connected to the power supply socket only
when this switch is in OFF position. If the plug
is connected to a receptacle while the power
switch is in the ON position, the power tool
will start operating immediately, which could
cause a serious accident.
▪ Make sure that the cord and the plug are in
order. If the replacement of the supply cord is
necessary, this has to be done by the manu-
facturer or his agent in order to avoid a safety
hazard.
FK 6522 ● FK 6524 ● FK 6526