Assembling The Appliance; Wall Mount; Charging The Battery - UFESA AE4415 Mode D'emploi

ASSEMBLING THE
APPLIANCE
Attaching the handle of the handstick
vacuum cleaner:
To attach the handle of the handstick
vacuum cleaner simply fold it upward
until it locks into position on the vacuum
cleaner. (Figure 1)
To fold it back down again press release
button "4" and this will free the clips
that attach it to the vacuum cleaner
(Figure 2).
Attaching the floor tool "8":
To attach the floor tool to the handstick
vacuum cleaner insert it into its housing
and press it so that it locks on to the
vacuum cleaner. (Figure 3)
To take it off again press the release
button "9" which will free the clips
that attach it to the vacuum cleaner
(Figure 4).
Attaching the handheld vacuum
cleaner:
Insert the handheld vacuum cleaner into
the handstick vacuum cleaner as shown
and lock into place. (Figure 5)
To take it off again press release button
"6" and remove it from the handstick
vacuum cleaner. (Figure 6)

WALL MOUNT

The charger support can be either
wall mounted or placed on the floor.
(Figures 7 & 8)
To use the charger base as a floor
stand:
Slot the wall mount section "15" into the
floor stand section "16" so that it locks
into position. (Figure 9)
Insert the jack for the charger "17"
into socket "A" on the wall mount.
(Figure 10)
To use the charger base as a wall
mount:
To install the wall mount "15", choose
a position close to an electrical wall
socket. Before fitting it, make sure that
there are no dangerous objects hidden
below the surface of the wall, such as
electrical wires, pipes, etc.
Place the wall mount against the wall
as shown in (Figure 11) and mark the
places where the screws will go. Once
the screws are fitted, place the wall
mount onto them and press it gently
downward to make it secure.
Insert the jack for the charger "17"
into socket "A" on the wall mount.
(Figure 10)

CHARGING THE BATTERY

Charge up the vacuum cleaner's
batteries for approximately 16 hours
before using it for the first time.
Insert the vacuum cleaner into its socket
(Figure 12). The charge indicator (12) will
light up. This indicator will remain lit as
long as the vacuum cleaner is plugged
in, even if the battery is fully charged.
The vacuum cleaner will become warm
while it is charging. This is quite normal
and will not interfere with the appliance's
safety or operation.
The vacuum cleaner can always be left
to charge when it is not in use. This will
ensure that the battery is always fully
charged and ready for use.
OPERATING INSTRUCTIONS
The AE4417 model has a luminous
indicator that shows the battery capacity
level when the appliance is working
(18). When the indicator remains in red
colour, it means that the battery is in low
level and needs to be charged.
Use as a handstick vacuum cleaner:
Take the handstick vacuum cleaner off
the charger unit and press the On/Off
button "1" (Figure 13).
The indicator "11" will light up, this
indicator shows that the rotating floor
tool "10" is working.
Make sure that none of the nozzles is
blocked and that the rotating floor tool
is clean.
Use as a handheld vacuum cleaner:
Take the handheld vacuum cleaner
off by pressing release button "6".
(Figure 6)
The suction nozzle on the handheld
vacuum cleaner can be adjusted
allowing the vacuum to get into awkward
places, to do this pull on it gently until it
is full extended. (Figure 14)
To slide the nozzle back in, press on the
release clip and push the nozzle back.
(Figure 15)
To pick up dry remains, vacuum in any
direction until the area is clean. Do
not overfill the container. Empty it out
regularly.
When storing or charging the handheld
vacuum cleaner, slot the suction nozzle
back into its parking position on the
handstick vacuum cleaner, making sure
that it is seated correctly. (Figure 5)