Technical Data - Scheppach MTP870H Mode D'emploi D'origine

3 Do not change the engine governor settings GB
or over-speed the engine. The governor controls the
maximum safe operating speed of the engine.
4 Do not run the engine at a high speed when you
are not tilling.
5 Do not put hands or feet near rotating parts
6 Avoid contact with hot fuel, oil, exhaust fumes
and hot surfaces. Do not touch the engine or muffler.
These parts get extremely hot from operation. They
remain hot for a short time after you turn off the unit.
Allow the engine to cool before doing maintenance
or making adjustments.
7 If the machine should start to make an unusual
noise or vibration, immediately shut off the engine,
disconnect the spark plug wire, and check for the
cause. Unusual noise or vibration is generally warn-
ing of trouble.
8 Use only attachments and accessories approved
by the manufacturer. Failure to do so can result in
personal injury.
9 Maintain the machine. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the machine's
operation. If damaged, have the machine repaired
before use. Many accidents are caused by poorly
maintained equipment.
10 Keep the engine and muffler free of grass, leaves,
excessive grease or carbon build up to reduce the
chance of a fire hazard.
11 Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
12 Never douse or squirt the unit with water or any
other liquid. Keep handles dry, clean and free from
debris. Clean after each use.
13 Observe proper disposal laws and regulations for
gas, oil, etc. to protect the environment.
14 Store idle machine out of the reach of children
and do not allow persons unfamiliar with the ma-
chine or these instructions to operate it. Machine is
dangerous in the hands of untrained users.
Service
Before cleaning, repair, inspecting, or adjusting, shut
off the engine and make certain all moving parts
have stopped. Disconnect the spark plug wire, and
keep the wire away from the plug to prevent acciden-
tal starting.
Have your machine serviced by qualified repair
personnel using only identical replacement parts.
This will ensure that the safety of the machine main-
tained.
Specific safety rules
1 Thoroughly inspect the area to be tilled, and
remove all debris and hard or sharp objects such as
stones, sticks, glass, wire, bones, etc.
2 Do not operate tiller in soil with large rocks and
foreign objects which can damage the machine.
3 Do not till above underground electric cables, tel-
ephone lines, water lines, gas line, pipes, or hoses.
If in doubt, contact your utility or telephone company
to locate underground services.
4 Keep all bystanders, children, and pets at least
23m away. If you are approached, stop the unit im-
mediately.
5 Walk, never run with the machine.
24 І 64
6 This unit has a clutch. Squeeze the clutch control
lever and check that i t returns automatically to the
neutral position. If it does not, have unit adjusted by
a qualified repair personnel.
7 Disengage clutch lever before starting the engine.
8 Start the engine carefully according to instruc-
tions and with feet well away from the tines.
9 The tines remain stationary when the clutch is
disengaged. If it does not, have unit adjusted by a
qualified repair personnel.
10 Always operate the machine from behind, never
pass or stand in front of the machine when the en-
gine is running.
11 Always hold the unit with both hands when oper-
ating. Keep a firm grip on the handlebars.
12 Be aware that the machine may unexpectedly
bounce upward or jump forward if the tines should
strike buried obstacles such as large stones, roots,
or stumps.
13 If the unit strikes a foreign object, stop the engine,
disconnect the spark plug, thoroughly inspect the
machine for any damage, and repair the damage
before restarting and operating the machine.
14 Use extreme caution when in reverse ornpulling
the machine towards you.
15 Do not overload the machine capacity by tilling
too deep in a single pass or at too fast a rate.
16 Never operate the tiller at high transport speeds
on hard or slippery surfaces.
17 Be careful when tilling in hard ground. The tines
may catch in the ground and propel the tiller forward.
If this occurs, let go of the handlebars and do not
restrain the machine.
18 Use caution when tilling near fences, buildings
and underground utilities. Rotating tines can cause
property damage or personal injury.
19 Exercise extreme caution when operating on or
crossing gravel drives, walks, or roads. Stay alert for
hidden hazards or traffic. Do not carry passengers.
20 Never leave the operating position when the
engine is running.
21 Always stop the engine when tilling is delayed or
when walking from one tilling location to another.
22 Keep unit clean of vegetation and other materials.
They may become lodged between the tines. Stop
the engine and disconnect the spark plug before
unclogging the tines.

6. Technical data

Engine:
Engine rating:
Engine working speed:
Working width:
Hoe blade diameter Ø:
Starting system:
Fuel:
Engine oil:
Tank capacity:
Weight:
Spark plug:
4-stroke engine,
160 ccm
3,3 kW/ 4,5 hp
3600 rpm
350/550/800mm
33 cm
reversing
starter
Unleaded petrol
min. 90 octane
max. 5%
bio-ethanol
0,55l (15W40)
0,91 l
48 kg
NGK BPR6ES