Timer Setting - Steba Induktion IK 50 Mode D'emploi

∙ Keep the cable away from hot surfaces
∙ Do not keep the appliance unattended during the usage.
∙ Never store anything on the appliance or cover the air inlets. Insert no sharp things
in the air in- and outlets.
∙ Never store the appliance outside or in a wet place.
∙ Do not immerse the appliance in water or any other liquid (Danger of electric
shock!). Protect the appliance from getting wet.
∙ Never use the appliance, if the cable or the glass plate is damaged, cracked or drop-
ped down.
∙ To avoid any dangers, never change anything at the appliance or conduct any re-
pair. Repairs and exchange of the power cord must only be done by an authorized
dealer.
∙ The appliance can get hot. Only transport after cooling down.
∙ The appliance must not be used with an external Timer or any other remote con-
trol.
∙ Danger. Appliance can get hot. Danger of burns!!
∙ Never put pots, set of instruments or any other metallic parts on the appliance.
These parts could get very hot, when the cooker is turned on. Never heat up closed
metallic cans. They could explode. The glass surface could show residual heat from
the heated pots.
∙ Never carry, when there are still pots or pans on it.
∙ Never put more than 5 kg on the top of the plate.
∙ Never use the appliance without supervision.
∙ Never use the appliance near to magnetic sensible items (e.g. magnetic cards etc.)
∙ Do not operate the device on any metal table because this may cause potential
serious danger to users and the appliance itself.
Implementing
∙ Plug the power plug into a suitable outlet and an acoustic signal sounds. While
plug on, the LED displays the temperature of induction cooker glass. When tempe-
rature lowers than 50°C, displaying „-L-". When temperature is higher than 50°C,
displaying „-H-".
∙ Place suitable cookware in the centre of the hotplate.
∙ Now press the AN/STANDBY switch once to turn the induction hotplate on. The
control lamps of "STUFE" and "TEMP." blink and an acoustic signal sounds, the
"-L-" or "-H-" in the display disappears. (NOTE: should no further operation in
30 seconds after pressing AN/STANDBY key, the control lamps of "STUFE" and "
TEMP." go off, the unit goes back to standby status automatically and the display
shows "-L-" or "-H-" again. To re-operate the unit, simply press ON/STANDBY key
once and other function keys.)
10
Power
The pot should be placed on the appliance.
Press the „AN/STANDBY" button. In the display "Stufe" is flashing. When there is no
adjustment within ca. 1min then the appliance returns to the stand-by modus.
Press the button "Stufe"(= means Power) and in the display you can see 5.
With the rotary knob the Wattage can be adjusted.
1 = 900 Watt* 2 = 915 Watt* 3 = 915 Watt
6 = 1290 Watt 7 = 1450 Watt 8 = 1550 Watt
All Power steps should be used to cook water or soups. If meat or vegetables should
be roasted, then the temperature function should be used to achieve a good result.
Temperature
This function should be used to roast meat or vegetables. Place the pot on the appli-
ance. Press the „AN/STANDBY" button. Then press the temperature button 2 times.
In the display appears 120°C. By turning the rotary knob the temperature can be
adjusted from 60-240°C. The build in sensor keeps the temperature at the adjusted
temperature. If the overheat temperature sensor switches the appliance off then the
displays shows E05. The appliance should then be cooled down for short time and can
be restarted.
Important: It is only possible to adjust either temperature or Power. Both together
are not possible.
It is always possible to switch during cooking from Temperature to Power, even when
the Timer is set. In the display the lights show what is adjusted

Timer Setting

Adjust as described before the Power or Temperature. Then press the Timer button.
In the display "0" is shown. Now you have ca 5sec time to adjust the in 5min steps
from 0-180min upwards and in 1 min steps back. When there is no adjustment within
5 sec the display returns to the chosen function. If this happens please redo the de-
scribed procedure.
Should the time be adjusted during the appliance is working and the Timer is wor-
king then press 1x the Timer button. At the display the Timer light is on. Now you
have ca 5 sec time to adjust the time with the rotary knob. After ca 5 sec the display
Temperature and Timer or Power and Timer until the time runs out and the appliance
returns to the stand by modus.
By pressing the „AN/STANDBY" button the program can be deleted. If no or a not
suitable pot is put on the appliance and adjust the Temperature or Power then a bee-
ping sound can be heard every 2 sec and at the display 3 lines are shown. The fan is
working. After a certain time (ca 15sec) the appliance returns to the stand-by modus.
4 = 950 Watt 5 = 1180 Watt
9 = 1750 Watt 10 = 2000 Watt
(*= cycled)
11