Cardin Elettronica 200/BL1924ASW Instructions D'utilisation page 19

Terminal board connections
7 CMN common for all inputs and outputs.
8 ELS electric lock output (fed continuously) 12 vdc - 15 W.
9-10 LC-CH2 Potential free contact for the activation of the courtesy light
(separate power supply vmax=30 vac/dc: Imax=1A) or the second
radio channel. Selection is carried out using jumper "j5".
11 CMN common for all inputs and outputs.
12 LP 24 vdc 25 W output for warning lights.
intermittent activation (50%), 12,5 W continuous activation
13 LS 24 vdc 3 W output for an indicator light.
14 CMN common for all inputs and outputs.
15 30 vdc controlled output, powering external loads
16 CMN common for all inputs and outputs.
17 30 vdc output, powering external loads
18 CMN common for all inputs and outputs.
19 TA (NO contact) opening button input
20 TC (NO contact) closing button input
21 TAL (NO contact) limited opening button input
22 TD (NO contact) dynamic button input
23 CMN common for all inputs and outputs.
24 TB (NC contact) stop button input (The opening of this contact inter-
rupts the cycle until a new movement command is given).
25 FTCS (NC contact) safety and control devices in input (stop photo-
cells). When the photocells are once again at rest and the pause time
has elapsed the device will move in the closing direction (only in the
automatic mode).
26 FTCI (NC contact) safety and control devices in input (photocells invert
the travel direction when an obstruction is detected). Opening this
contact will provoke a travel direction inversion during closure due to
the cutting in of the safety device.
27 EMRG2 (NO) emergency manoeuvre input 2
28 EMRG1 (NO) emergency manoeuvre input 1
29 CMN common for the emergency buttons
30 Inner conductor for radio receiver antenna (if an external antenna is
fitted use a coaxial type cable RG58 with an impedance of 50Ω).
31 Outer conductor for radio receiver antenna
B1 Signal buzzer "via radio" mode
CSER Serial connection (only for diagnostics)
D1 Six-segment LED display
DS1 Selection dip-switch
F1 10A blade fuse (motor power protection)
(5)
F2 10A blade fuse (motor protection during battery operation)
(5)
F3 4A blade fuse (24v circuit protection)
(5)
F4 4A blade fuse (24v circuit protection during battery operation)
(5)
F5 4A blade fuse (electric lock protection)
(5)
j1 Battery connection
.
(1)
.
(1)
Note The total of the 2 external device outputs must not exceed 10 W.
(1)
ALL UNUSED NC CONTACTS MUST BE jUMPED and consequently the
security device test must also be deactivated (FTCI , FTCS - Dip 7 and Dip
8 "OFF") . If you want to activate the FTCI, FTCS test both the transmission
and receiver parts of the security devices must be connected to the binding
post marked "CTRL 30 vdc". If the test is active there will be a 1 second
delay between the command transmission and movement of the gate/s.
Switch on the power and make sure that the indicator LEDs are in the fol-
lowing condition.
- L1 Power on
- L2 Battery charging
- L3 Wrong battery connection
- L4 Transmitter code programming indicator
- L5 Indicator for the blocking button "TB"
- L6 Indicator for the inverting photoelectric cells "FTCI"
- L7 Indicator for the stop photoelectric cells "FTCS"
- L8 Indicator for the opening button "TA"
- L9 Indicator for the opening button "TC"
- L10 Indicator for the limited opening button "TAL"
- L11 Indicator for the sequential command "TD/CH1"
Note : This LED is "ON" when the battery is charging.
(2)
Note : If this LED is "ON" invert the battery power cables immediately.
(3)
Note : Check that the activation of the safety devices switches the cor-
(4)
responding LEDs off.
If the green power on LED "L1" doesn't light up check the condition of the
fuses and the power cable connection at the transformer primary.
If one or more of the safety LEDs do not light up check the contacts of the
relative security devices and check that the unused safety device contacts
have been bridged.
j2 Transformer secondary protection
j3 Enable transmitter memorisation via radio
j4 Radio channel selection
j5 Binding posts 15, 16 selection (courtesy light/CH2 via radio)
MM Transmitter code memory module
P1 Programming button (PROG)
P2 Transmitter code memorization button (MEMO)
P3 Transmitter code cancellation button (DEL)
R1 Radio frequency module, 433 MHz for S449 transmitters
Note : These are automotive type blade fuses (max. voltage 58 v)
(5)
19
ON
OFF
(2)
OFF
(3)
OFF
ON
(4)
ON
(4)
ON
(4)
OFF
OFF
OFF
OFF