Alpine DVA-9860 Mode D'emploi page 58

1 Antenna Receptacle
2 Power Antenna Lead (Blue)
Connect this lead to the +B terminal of your power antenna,
if applicable.
NOTE
This lead should be used only for controlling the vehicle's
power antenna. Do not use this lead to turn on an amplifier or
a signal processor, etc.
3 Remote Turn-On Lead (Blue/White)
Connect this lead to the remote turn-on lead of your
amplifier or signal processor.
4 Audio Interrupt In Lead (Pink/Black)
5 Illumination Lead (Orange)
This lead may be connected to the vehicle's instrument
cluster illumination lead. This will allow the backlighting of
the DVA-9860 to dim whenever the vehicle's lights are
turned on.
6 Switched Power Lead (Ignition) (Red)
Connect this lead to an open terminal on the vehicle's fuse
box or another unused power source which provides (+)12V
only when the ignition is turned on or in the accessory
position.
7 Battery Lead (Yellow)
Connect this lead to the positive (+) post of the vehicle's
battery.
8 Ground Lead (Black)
Connect this lead to a good chassis ground on the vehicle.
Make sure the connection is made to bare metal and is
securely fastened using the sheet metal screw provided.
9 Remote Control Input Lead (White/Brown)
Connect the external Alpine product to the remote control
output llead.
! Monitor Control Lead (White/Pink)
Connect this to the Monitor Control Lead of the touch panel-
compatible monitor.
" Video Output Connector
This connector is used in combination with the video inputs
of another video product (Touch panel compatible monitor,
etc.)
# External Junction Box Connector
Connect to the external junction Box (included)
$ External Junction Box
Use when connecting optical digital cable or the remote
control interface box.
Connect to the external junction box connector.
• Do not install the external junction box at a location subjected
to water such as under the floor mat or air conditioner. This
may cause a malfunction.
• Do not bundle the external junction box cable with other audio cables.
Doing so may induce noise into your system.
• Keep the external junction box away from the Antenna cables
and the rear side of the unit, otherwise noise may be generated
when receiving radio broadcast.
To prevent external noise from entering the audio system.
• Locate the unit and route the leads at least 10 cm away from the car harness.
• Keep the battery power leads as far away from other leads as possible.
• Connect the ground lead securely to a bare metal spot (remove any paint, dirt or grease if necessary) of the car chassis.
• If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries various noise
suppressors, contact them for further information.
• Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information.
% Digital Output Terminal (Optical)
Use when combining optical digital input compatible
products.
& Remote Control Interface Connector
Connect to the remote control inerface box.
• Use a steering remote control extension cabel (included) if
necessary.
( Right Front (+) Speaker Output Lead (Gray)
) Right Front (–) Speaker Output Lead (Gray/Black)
~ Right Rear (–) Speaker Output Lead (Violet/Black)
+ Right Rear (+) Speaker Output Lead (Violet)
, Left Rear (+) Speaker Output Lead (Green)
- Left Rear (–) Speaker Output Lead (Green/Black)
. Left Front (–) Speaker Output Lead (White/Black)
/ Left Front (+) Speaker Output Lead (White)
: Rear Output RCA Connectors
RED is right and WHITE is left.
; Front Output RCA Connectors
RED is right and WHITE is left.
< Subwoofer RCA Connectors
RED is right and WHITE is left.
= Fuse Holder (10A)
> Ai-NET Connector
Connect this to the output or input connector of other
product (CD Changer, Equalizer, iPod adapter,* etc.)
equipped with Ai-NET.
NOTES
You can input TV/video sound by connecting an optional Ai-
NET/RCA Interface cable (KCA-121B) to this component.
* If you connect to the iPod, you need the optional adapter
(KCA-420i). For details on connection, refer to the Owner's
Manual of the KCA-420i.
? Power Supply Connector
@ System Switch
When connecting a processor or divider using Ai-NET, place
this switch in the EQ/DIV position. When no device is
connected, leave the switch in the NORM position.
NOTE
Be sure to turn the power off to the unit before changing the
switch position.
[ Ai-NET Cable (Included with CD Changer)
\ RCA Extension Cable (Sold Separately)
57
-EN