Switching The Phase; Graphic Equalizer Adjustments - Alpine DVA-9860 Mode D'emploi

8
Select the desired channel by pressing g or
f.
When L+R is selected :
FRONT 1 → FRONT 2 → REAR → CENTER →
SUBWOOFER → FRONT 1
When L/R is selected :
FRONT 1L → FRONT 1R → FRONT 2L → FRONT 2R →
REAR L → REAR R → CENTER → SUBWOOFER →
FRONT 1L
• The speakers display differs, depending on the connected speakers.
9
Adjust the calculated time correction value (0.00 to
20.00ms) by turning and then pressing the Rotary
encoder.

Switching the Phase

10
Switch the phase (PHASE) by turning and then
pressing the Rotary encoder.
11
To adjust other channels, repeat steps 8 to 10.
12
When the setting is complete, press and hold
CENTER f. for at least 2 seconds.
The unit returns to the normal mode.
Press CENTER f. to select another item to be set.
• When the speaker is set to the "OFF" mode, the TCR for that
speaker cannot be set. Refer to "Setting the Speakers" (page 30).
• The adjustment value for FRONT2 (Speakers) which is adjusted in
time correction, is also applied to the front speakers in "Setting
Bass Focus" (page 34).
• The adjustment (AUTO TCR) cannot be automatically set on this
unit.
• When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 37.
32
-EN

Graphic Equalizer Adjustments

The graphic equalizer allows you to modify the sound using 31 bands
each for the front (left and right), rear (left and right) and centre
speakers. An additional 10 bands are available for the subwoofer. This
allows you to customize the sound to suit your taste.
1
Check that Defeat mode is off (page 17).
2
Press and hold CENTER f. for at least 2 seconds.
The audio processor control mode is activated.
3
Select the G-EQ mode by pressing CENTER f.
repeatedly.
4
Select L+R or L/R by pressing and holding BAND
for at least 2 seconds.
L+R: Sets the same adjustment values for the left and
right channels.
L/R: Different adjustment values can be set for the left
and right channels.
When parametric EQ is adjusted, this setting will be
turned off.
5
Select the desired channel by pressing g or
f.
When L+R is selected :
FRONT → REAR → CENTER → SUBWOOFER →
FRONT
When L/R is selected :
FRONT L → FRONT R → REAR L → REAR R → CENTER
→ SUBWOOFER → FRONT L
• The speakers display differs, depending on the connected speakers.
6
Select the frequency by turning and then pressing
the Rotary encoder.
Adjustable frequency:
FRONT/REAR/CENTER: 20Hz - 20kHz (in 1/3 octave
SUBWOOFER:
7
Adjust the level (LEVEL) (±9dB 1dB step) by
turning and then pressing the Rotary encoder.
8
To adjust other channels, repeat steps 5 to 7.
9
When the setting is complete, press and hold
CENTER f. for at least 2 seconds.
The unit returns to the normal mode.
Press CENTER f. to select another item to be set.
• When the speaker is set to the "OFF" mode, the graphic equalizer
for that speaker cannot be set. Refer to "Setting the Speakers"
(page 30).
• Check the playable frequency ranges of the connected speakers
before making the equalizer adjustments. If the speaker's playable
frequency range is 55 Hz to 30 kHz, for example, adjusting the
40 Hz or 20 Hz band has no effect. Additionally, you may overload
and damage the speakers.
• When graphic EQ is adjusted, the adjustment for parametric EQ
becomes ineffective.
• When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 37.
steps)
20Hz - 160Hz (in 1/3 octave
steps)