The Machine Table Extensions - Evolution R255 SMS-DB Notice Originale

www.evolutionpowertools.com
THE BEVEL NECK
Note: The bevel neck is supplied fitted to the
Rotary table. The bevel neck should be adjusted to
the 0˚ position.
• Slacken the Bevel Locking screw using the Bevel
Locking Handle. (Fig. 66)
• Rotate the bevel neck to the vertical position so
that it rests against the 0˚ stop.
• Tighten the Bevel Locking Handle.
INSERTING THE CARRIAGE SLIDE
IMPORTANT: If for any reason (transit damage,
unpacking error, operator mistake, etc.) the
locating pins at the tip of the carriage slide
arms have been 'tripped' , the sliding carriage
cannot be fitted into the bevel neck or onto the
cutting head.
The locating pins must be reset, if either or
both have been 'tripped' prematurely. (Fig.10)
Resetting the locating pins:
• Gently push the protruding lug into the
Carriage arm.
• Gently ease the locating lug deployment
plunger forward by using a flat bladed
screwdriver (not supplied) as a lever. (Fig. 11)
The carriage slides two (2) arms should be inserted
through the two linear bearings contained within
the bevel neck.
The carriage slide should be inserted from the
back ensuring that the 'Evolution' logo is the
correct way up. (Fig. 12)
• Slide the sliding carriage arms through the bevel
neck for approximately half of their length.
• Screw the carriage slide locking screw into the
threaded hole above the right hand arm of the
carriage slide. (Fig. 13)
Note: Ensure that the anti-vibration spring is fitted
underneath the hand knob before fitting the
locking screw into its service position.
• Tighten the locking screw to lock the sliding
carriage into the desired position.
ATTACHING THE CUTTING HEAD
• Align the cutting head with the two (2) sliding
carriage arms. (Fig. 14a)
• Push the cutting head onto the Carriage arms
firmly until the 'click' of the Locating Pins
deploying is heard. (Fig. 14b)
Note: The deployed locating pins must be fully
visible when viewed from the side of the cutting
head. (Figs. 15a, 15b) The Locating Pins are
coloured green to make identification easy.
Two M6 x 12mm screws are supplied which
should be screwed into the head of the saw
where it meets the rear sliding carriage rails.
This secures the rails in place reducing any
wobble that may occur. (Fig. 15c) The two screws
are supplied with the rear cable guide clamp in
the packaging. These 2 screws can be fitted with
the supplied 4mm hex key.

THE MACHINE TABLE EXTENSIONS

(Fig. 16)
Two (2) machine table extension pieces are
provided with this machine.
To fit the table extensions:
• Remove the socket headed screws from the
table using the supplied 4mm hex key. (Fig. 17)
• Position the Extension piece onto the table
and secure it into its service position using the
socket headed screws.
• Repeat for the second Extension piece.
ROUTING THE POWER CABLE
WARNING: This machine is equipped with
a mains cable and a moulded plug which
satisfies the regulations of the receiving
country. This cable and plug, if damaged,
should only be replaced with genuine
Evolution replacement parts and be fitted by a
competent technician.
• Ensure that the cutting head is in the
down position.
• Ensure that the carriage slide is in its most
forward position and locked. (Fig. 18)
From the motor the mains cable is pre-routed
through the front cable guide. The cable should
then be routed rearwards. (Fig. 19)
The cable should be inserted into the rear cable
guide/clamp. For 230v models, ensure the Cable
Grip Component is inside the cable guide when
the cable passes through.
This guide/clamp should then be fastened to
the rear sliding carriage cross piece (right hand
side) using the self tapping cap screw (included).
(Fig. 20)
25
EN