Technical Data; Dimensions, Weights, Ambient Conditions; Supply Voltage (External); Cable - Balluff BTL5-S1 Série Notice D'utilisation

BTL5-S1_ _-M_ _ _ _-B/Z-DEX_-K_ _/KA_ _
Micropulse Transducer - Rod Style
7

Technical Data

Typical values at DC 24 V, room temperature and BTL5 with nominal length 500 mm. Ready for operation at once.
Full accuracy after warm up. Values are with BTL-P-1013-4R, BTL-P-1013-4S or BTL-P-1012-4R magnet rings or
with BTL2-S-6216-8P-Ex, BTL2-S-5113-4K-Ex, BTL2-S-4414-4Z-Ex or BTL2-S-4414-4Z01-Ex floats.
Resolution (LSB)
depending on version:
BTL5-S1_2... 5 µm
BTL5-S1_3... 10 µm
BTL5-S1_4... 20 µm
BTL5-S1_5... 40 µm
BTL5-S1_8... 50 µm
Non-linearity
for resolutions of 5 µm or 10 µm
otherwise
Output data
Update rate f
max
Hysteresis
Repeatability
(resolution + hysteresis)
Temperature coefficient
(6 µm + 5 ppm * nominal length)/K
Shock loading 100 g/6 ms
per EN 60068-2-27
1
Continuous shock 100 g/2 ms
per EN 60068-2-29
1
Vibration 12 g, 10 bis 2000 Hz
per EN 60068-2-6
1
(take care to avoid inherent reso-
nances of protective tube)
Pressure up to 350 bar
when installed in a hydraulic cylin-
der (Zone 1)
Individual specifications as per
1
Balluff factory standard
7.1 Dimensions, weights,
ambient conditions
Nominal length < 4000 mm
Dimensions ➥ ➥ ➥ ➥ ➥ Fig. 3-1
Weight ca. 2 kg/m
Housing Stainless steel
Pressure tube Stainless steel 1.4571
diameter 10.2 mm
wall thickness 2 mm
e-modulus ca. 200 kN/mm
Mounting threads
M18 × 1.5 or 3/4"-16UNF
Operating temp. –40 °C to +60 °C
Humidity < 90 %, non-dewing
Protection rating per IEC 60529
IP 67 when closed up
7.2

Supply voltage (external)

Regulated supply voltage
BTL5-S1... DC 20 to 26 V
Ripple < 0.5 V
pp
Current draw < 90 mA
Inrush < 3 A/0.5 ms
Polarity reversal protection built-in
Overvoltage protection
Transzorb diodes
Electric strength
GND to housing 500 V DC
7.3 Control signals
Interface
Clock input
(via optical coupler)
Clock frequency max. 500 kHz
Output data
Position information +Data, –Data
± 30 µm
For safety reasons the
± 2 LSB
maximum current load for
the RS 485/422 interface
< 2 kHz
is 20 mA.
< 1 LSB
7.4 Connection
< 2 LSB
+Clk, –Clk, +Data, –Data, 24 V, GND
Cable, twisted-pair, shielded
max. length 400 m
7.5

Magnet rings

(order separately)
BTL-P-1013-4R, BTL-P-1013-4S,
BTL-P-1012-4R
Installation dimensions ➥ ➥ ➥ ➥ ➥ Fig. 3-5
Weight
Material
Operating temp. –40 °C to +85 °C
The transducer is
certified with IECEx
PTB 11.0035X. The
current issue can be
found at
www.iecex.com
2
In our accredited EMC Laboratory,
proof has been documented that
these Balluff products meet the
EMC requirements of the follow-
ing product standard:
EN 61326-2-3
(noise immunity and emission)
RS 485/422
+Clk, –Clk
24 or 25 bit serial
approx. 10 g
anodized aluminum
The
transducer
is certified
under KC
certificate
number 13-
AV4BO-0631.
The CE Mark verifies
that our products meet
the requirements of the
current EMC Directive.
Ignition Class "d"
Flameproof enclosure
Floats (order separately)
7.6
Material Stainless steel
Operating temp. –20 °C to +120 °C
Float BTL2-S-6216-8P-Ex
Installation dimensions ➥ Fig. 3-7
Weight 69 g
Pressure rated to 15 bar
Float BTL2-S-5113-4K-Ex
Installation dimensions ➥ ➥ ➥ ➥ ➥ Fig. 3-8
Weight 34 g
Pressure rated to 40 bar
Float BTL2-S-4414-4Z-Ex
Installation dimensions ➥ ➥ ➥ ➥ ➥ Fig. 3-9
Weight 34 g
Pressure rated to 20 bar
Float BTL2-S-4414-4Z01-Ex
Installation dimensions ➥ ➥ ➥ ➥ ➥ Fig. 3-10
Weight 52 g
Pressure rated to 20 bar
7.7

Compatible devices

(optional)
Display:
BDD-AM 10-1-SSD
display and limit controller
with 2 relay outputs
Emission tests:
RF Emission
EN 55011
Noise immunity tests:
Static electricity (ESD)
EN 61000-4-2 Severity level 3
Electromagnetic fields (RFI)
EN 61000-4-3 Severity level 3
Fast transients (Burst)
EN 61000-4-4 Severity level 3
Surge
EN 61000-4-5 Severity level 2
Line-induced noise induced by
high-frequency fields
EN 61000-4-6 Severity level 3
Magnetic fields
EN 61000-4-8 Severity level 4
english
11