Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
OPERATION
Screwdriving operation
Place the point of the driver bit in the screw head and
apply pressure to the tool. Then switch the tool on.
When the clutch cuts in, the motor will stop automati-
cally. Then release the switch trigger.
NOTE:
•
Make sure that the driver bit is inserted straight
in the screw head, or the screw and/or bit may
be damaged.
Limits of fastening capacity
Use the tool within the range of the revolution angle up
to 360°. If you use the tool beyond the upper limit of this
range, the clutch does not work. And the tool cannot
deliver enough fastening torque (LEDA #A blinks in
purple slowly or lights up in purple).
NOTE:
•
The revolution angle means the angle which
a screw/bolt revolves when the tool attains to
100% from 50% of desired torque.
•
Use of a low temperature conditioned battery
cartridge may sometimes give warning for
battery cartridge capacity by warning lamp and
beeper which makes the tool stop immediately.
In this case, the fastening capacity may be
inferior to the specification on this manual even
if a charged battery cartridge is used.
MAINTENANCE
CAUTION:
•
Always be sure that the tool is switched off and
the battery cartridge is removed before attempt-
ing to perform inspection or maintenance.
•
Never use gasoline, benzine, thinner, alcohol
or the like. Discoloration, deformation or cracks
may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
OPTIONAL
ACCESSORIES
CAUTION:
•
These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments
might present a risk of injury to persons. Only use
accessory or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
•
Makita genuine battery and charger
•
Adjust grip
•
Protector
•
Grip Base Set
•
Grip 37
•
Receiver RCV02
•
Software Installing disc (CD-ROM) except for
Model DFT041R
•
USB-serial adapter
•
RS-232C cable
NOTE:
•
Some items in the list may be included in the
tool package as standard accessories. They
may differ from country to country.
MAKITA LIMITED ONE YEAR
WARRANTY
Warranty Policy
Every Makita tool is thoroughly inspected and tested before
leaving the factory. It is warranted to be free of defects from work-
manship and materials for the period of ONE YEAR from the date
of original purchase. Should any trouble develop during this one
year period, return the COMPLETE tool, freight prepaid, to one
of Makita's Factory or Authorized Service Centers. If inspection
shows the trouble is caused by defective workmanship or mate-
rial, Makita will repair (or at our option, replace) without charge.
This Warranty does not apply where:
•
repairs have been made or attempted by others:
•
repairs are required because of normal wear and tear:
•
the tool has been abused, misused or improperly
maintained:
•
alterations have been made to the tool.
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY
INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES FROM THE SALE OR USE OF THE
PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING
AND AFTER THE TERM OF THIS WARRANTY.
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES,
INCLUDING IMPLIED WARRANTIES OF "MERCHANTABILITY"
AND "FITNESS FOR A SPECIFIC PURPOSE," AFTER THE ONE
YEAR TERM OF THIS WARRANTY.
This Warranty gives you specific legal rights, and you may also
have other rights which vary from state to state. Some states do
not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to
you. Some states do not allow limitation on how long an implied
warranty lasts, so the above limitation may not apply to you.
11 ENGLISH
Publicité
Table des Matières
