Festool HKC 55 EB Notice D'utilisation Originale page 10

English
Lower guard function
a. Check the lower guard for proper closing
before each use. Do not operate the saw if
the lower guard does not move freely and
close instantly. Never clamp or tie the
lower guard into the open position. If the
saw is accidentally dropped, the lower
guard may be bent. Raise the lower guard
with the retracting handle and make sure it
moves freely and does not touch the blade
or any other part, in all angles and depths
of cut.
b. Check the operation of the lower guard
spring. If the guard and the spring are not
operating properly, they must be serviced
before use. Lower guard may operate slug­
gishly due to damaged parts, gummy de­
posits, or a build-up of debris.
c. The lower guard may be retracted man­
ually only for special cuts such as "plunge
cuts" and "compound cuts". Raise the low­
er guard by the retracting handle and as
soon as the blade enters the material, the
lower guard must be released. For all oth­
er sawing, the lower guard should operate
automatically.
Always observe that the lower guard is
d.
covering the blade before placing the saw
down on bench or floor. An unprotected,
coasting blade will cause the saw to walk
backwards, cutting whatever is in its path.
Be aware of the time it takes for the blade
to stop after switch is released.
Function of the guide wedge [1-5]
Use the correct saw blade for the guide
a.
wedge, where possible. The function of the
guide wedge is restricted if using saw
blades with a thicker blade core. To en­
sure that the guide wedge functions prop­
erly, make sure the blade core of the saw
blade is thinner than the guide wedge and
that the tooth width is greater than the
thickness of the guide wedge. Expect in­
creased risk of kickback when using a
thicker saw blade.
Do not operate the saw if the guide wedge
b.
is bent. Even the slightest problem can
cause the guard to close more slowly.
Further safety instructions
– This electric power tool cannot be instal­
led in a work bench. The electric power
tool may become unsafe and cause serious
accidents if installed in benches from other
10
manufacturers or self-manufactured work
benches.
– Never place your hands into the chip ejec­
tor. You may injure yourself on rotating
parts.
– Use suitable detectors to determine if util­
ity lines are hidden in the work area or
call the local utility company for assis­
tance. Aontact with electric lines can lead
to fire and electric shock. Damaging a gas
line can lead to explosion. Penetrating a
water line causes property damage or may
cause an electric shock.
Wait until the power tool stops completely
–
until placing it down. The tool can become
entangled and lead to a loss of control of
the power tool.
– Do not use the machine for overhead work.
Harmful/toxic dust may be produced dur­
–
ing your work (e.g. paint containing lead,
certain types of wood and metal). Inhaling
or coming into contact with this dust may
represent a hazard for operating personnel
or persons in the vicinity. Comply with the
safety regulations that apply in your coun­
try.
Wear a P2 dust mask to protect your
health.
Ensure that enclosed spaces are adequately
ventilated and, if necessary, connect a mobile
dust extractor.
–
Wear suitable personal protective equip­
ment: Ear protection, protective goggles,
dust mask for work that generates dust,
protective gloves for working with rough
materials and for changing tools.
Harmful/toxic dust may be produced dur­
–
ing your work (e.g. paint containing lead,
certain types of wood or metals). Contact
with or inhalation of this dust may pose a
risk for the operating personnel or persons
in the vicinity. Comply with the safety regu­
lations that apply in your country.
– Check whether there are any signs of dam­
age to the housing components, such as
cracks or stress whitening. Have any dam­
aged components repaired before using the
power tool.
Do not use power supply units or third-
–
party battery packs to operate cordless
power tools. Do not use third-party charg­