Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
STEAM FUNCTION
Making Cappuccino
1.
Make espresso as described above using big enough cups.
(11). Espresso buttons
2.
Press steam button
light keep on, the machine is pre-heating.
3.
Fill a container with approximately 60 to 100 ml of cold milk.
Note :
•
For the best results, use a narrow and relatively small container that can be slipped
under the steam nozzle.
•
When choosing the size of the milk container, keep in mind that the milk volume will
increase by two to three times.
•
We recommend using pasteurized or UHT milk at fridge temperature, and to avoid
using non-pasteurized or skimmed milk.
4.
Place the steam nozzle (G1) into a container filled with milk.
5.
Turn the knob (L) from preheat (L1) to steam position (L2) (25), steam button white light
flashes, the machine starts to make steam.
Note : For best results, foam the milk near the bottom of the container for approximately 10
seconds, taking care not to touch the bottom. Then slowly tilt the container and move the
nozzle upwards until it is almost at the surface of the milk. Make sure that the nozzle does
not leave the milk. To get a great foam, move the container in circular motions (26).
6.
Once you have achieved the best foam turn the knob back to preheat position (27).
Note : To prevent overheating the milk, do not use the steamer for more than 45 seconds
(for 100 ml of milk).
7.
Spread the milk froth over the cup(s) of espresso.
Note :
•
If you wish to make more than one cappuccino, first make all the espressos, then make
the milk froth.
•
Clean the steam nozzle immediately after use to ensure it does not get clogged up with
milk residue. See "Cleaning the steam nozzle".
IMPORTANT! Warning! To prevent the milk from spattering, do not lift the
nozzle out of the milk when using "steam" mode.
IMPORTANT! Warning! The steam nozzle is still hot! Be careful you do not
burn yourself!
IMPORTANT! After switching off the steam function, clean the nozzle
immediately and carefully, as set out in the section: CLEANING AND
MAINTENANCE .
Hot water preparation
1.
The machine is in standby mode.
2.
Place a container under the steam nozzle.
3.
Turn the knob to the position (L2) (25). Espresso buttons white lights turn off, steam
button white light flash. Machine starts making hot water and it will stop when turn the
knob back to the position pre-heating (L1) (27).
4
white light off, steam button orange
4.
Espresso buttons white lights keep on, steam button white light off.
GOOD TO KNOW – PRACTICE AFTER USING STEAM
•
If you want to make an espresso after using the steam function, you need to cool down
your coffee machine to avoid burnt coffee.
•
Press steam button
, if espresso buttons
temperature in boiler is too high, please do not make coffee right now. You need to
lower temperature.
•
Immerse the steam nozzle in a container filled with 60 ml of water.
•
Turn the knob from preheat (L1) back to steam position (L2) (25) to make hot water.
Stop make hot water until temperature goes down to pre-set value, then turn the knob
from steam to preheat position. Espresso buttons white light keep on.
SETTING THE COFFEE VOLUME
1.
The machine is in standby mode.
2.
Press or for 3 seconds. Selected espresso button orange light flashes.
3.
Release the button and start set coffee volume.
4.
Press the button as soon as the desired volume is reached.
5.
Both espresso buttons orange lights flash 3 times to confirm the new setting.
6.
The machine goes back to the standby mode.
Note : Programmable quantity for espresso 1 cup (15-65 ml, default volume 30 ml), 2 cups
(30-130 ml, default volume 60 ml).
RECOVER DEFAULT COFFEE VOLUME
1.
The machine is in steam pre-heat status.
2.
Press
for 3 seconds. 2 espresso buttons
3.
Water pump work one time.
4.
Default coffee volume is now recovered.
5.
The machine goes back to steam pre-heat status.
CLEANING AND MAINTENANCE
Unplug (J) before each clean and let the appliance cool down first.
„ Machine : Clean the outside of the appliance with a damp sponge when you think it
necessary. Do not use detergent or abrasive products. Do not use solvents or abrasive
detergents to clean the coffee machine.
„ Water tank : Rinse the inside of the tank regularly. When a fine white layer appears in the
tank, descale the appliance (refer to the section on descaling).
„ Drip tray : Clean the drip tray (I) and its grid (H) using water and a little mild detergent
(30-31). Rinse and dry.
„ Filter holder, filters : Using a damp cloth, clean the filter holder mount regularly in order
to remove possible coffee residues stuck to the surface. In order to prolong the useful
life of the watertight seal on the brewing head, do not put the filter holder back in place if
the coffee machine has not been used for extended periods. To remove any deposits that
could block the flow of your 1 or 2 cup filter, you may use the needle.
orange light flash, it means the
orange light flash one time.
5
Publicité
Table des Matières
