Publicité
GB
Obstacles/risk of crushing
• There should not be any obstructions in the exten-
sion area of the awning. There is the hazard of
people being crushed.
• There are crushing and cutting area between the
movable parts of the awning. Clothing or body
parts can be seized by these moving parts.
• Any additional loads of the awning through
attached objects or through rope tensioning may
lead to damages and falling of the awning and
therefore are not permitted.
Cleaning and maintenance work in the
extension area of the awning
• It should be ensured that the awning is not
extended when cleaning and maintenance work
(e.g. building cleaners) is being carried out.
Maintenance
• Safe and risk-free use of the awning can be guar-
anteed only if the awning is checked and main-
tained on a regular basis. Inspect the awning reg-
ularly for signs of wear or damage to its covering
material or frame.
• If any damages are identified, a professional
should be given the tasks of repairing it. Awnings
that are in need of repair should not be used.
• Check the awning regularly for any signs of wear
or damages
Installation and use
What is included
► Scope of delivery – p. 2
1. Awning
2. Screw, washer, nut (2×)
3. Wall/ceiling bracket (2×)
4. Crank handle
• Instructions for use
• Gauge for angle of tilt
Note: should any part be missing or dam-
aged, please contact your dealer.
Designation of awning components (general)
► P. 2, fig. 5
1. Cloth shaft
2. Support tube/bracket tube
3. left folding arm
4. Awning cloth
5. Drop rod/front profile
6. Valance
7. Fastening console
8. Cloth shaft holder
9. Gearbox
10. right folding arm
Fitting
Keep the following aids/tools at hand for installation:
• Spirit level
• Plumb line
• Tape measure
• Chalk or pencil
• Wrench A/F13, 16, 17, 18, 19
28
• Rubber mallet
• Stepladder
• (Hammer) drill
• select a suitable drill for the installation foundation
(Ø corresponding to dowel)
► Assembly – p. 3
Note: Two people must perform the
installation. A ladder is necessary. The
awning must be installed exactly horizon-
tally to ensure trouble free extension and
retraction.
Note: Please note that the bracket must
be installed about 10cm (Z) from the end
of the awning (► P. 3, fig. 2).
DANGER! Risk of injury! Never position
the selected fastening material in mortar
joints. Please observe specified edge dis-
tances. Make sure that there is enough
load-bearing capacity (masonry/wall
material) above the fastening holes to
ensure that there is no risk of any damage
to the masonry or wall material caused by
the forces acting on an extended awning.
DANGER! Risk of injury! In case of low
installation, please ensure that there are
no objects within the swivel range.
DANGER! Risk of injury! Strong forces
act on an awning when it is windy. An
incorrectly mounted awning can tear
loose and cause serious injuries.
WARNING! Danger of falling! Ensure a
stable stance during the installation.
Determine the height at which the awning is to be fas-
tened to the wall. If the awning is to be installed above
a door, the clearance above the door must be at least
20 cm. Please also observe the inclination angle of
the awning. The minimum inclination angle of the
cloth to the water drainage in case of rain must be
14°. After installation, the angle can be easily
changed as required. The front drop rod (front profile)
should have a clearance height of at least 2.5 m when
extended.
• Installation height: ► P. 3, fig. 1
– α = 10°
– α = 30°
– α = 45°
– Transfer the dimensions to the appropriate posi-
tion on the wall (► P. 3, fig. 2).
– X = 2400–2450 mm
– Y1 = 90 mm
– Y2 = 50 mm
– For this purpose, draw an exact horizontal line on
the wall at the desired height. Use a long tape
measure to do so, and check the position of the
line using a spirit level.
– To determine the position of the boreholes, slip
one bracket respectively onto the support tube in
the vicinity of an arm holder (20 cm to the left or
C = A + H × 0,17
C = A + H × 0,5
C = A + H × 0,71
Publicité
