Publicité
Liens rapides
Page 1 of 21
CP0444
FITTING INSTRUCTIONS CP0444 AERO CRASH PROTECTORS
T
.
HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE
S
.
OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY
D
.
O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT
P
.
LEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS
OR HAVE FITTED BY A QUALIFIED TECHNICIAN.
P
LEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE WAY OF
.
MOUNTING TO THE BIKE
I
,
N THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS
.
THESE RUBBER WASHERS CAN BE THROWN AWAY
DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM:
WWW.RG-RACING.COM
R&G Racing
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
www.rg-racing.com
Email:
info@rg-racing.com
Publicité
Manuels Connexes pour R&G CP0444
Sommaire des Matières pour R&G CP0444
- Page 1 Page 1 of 21 CP0444 FITTING INSTRUCTIONS CP0444 AERO CRASH PROTECTORS HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT...
- Page 2 Page 2 of 21 CP0444 TOOLS REQUIRED GENERAL TORQUE SETTINGS 8, 10, 17mm A/F SOCKET & WRENCH M4 BOLT = 8Nm • M5 BOLT = • METRIC HEX KEY BIT SET M6 BOLT = TORQUE WRENCH (UP TO 50Nm) •...
- Page 3 Page 3 of 21 CP0444 LHS & RHS EXPLODED ASSEMBLY VIEW R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...
- Page 4 Page 4 of 21 CP0444 Picture 1 Picture 2 Picture 3 Picture 4 Picture 5 Picture 6 Picture 7 Picture 8 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com...
- Page 5 Page 5 of 21 CP0444 Picture 9 Picture 10 Picture 11 Picture 12 Picture 13 Picture 14 Picture 15 Picture 16 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com...
- Page 6 Page 6 of 21 CP0444 Picture 17 Picture 18 Picture 19 Picture 20 Picture 21 Picture 22 Picture 23 Picture 24 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com...
- Page 7 Page 7 of 21 CP0444 Picture 25 Picture 26 Picture 28 Picture 27 Picture 29 Picture 30 Picture 31 Picture 32 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com...
- Page 8 Page 8 of 21 CP0444 Picture 34 Picture 33 Picture 36 Picture 35 Picture 37 Picture 38 FITTING INSTRUCTIONS Before removing engine bolts, ensure the bike is upright and supported by a suitable engine stand or jack placed under the sump of the motorbike to support the partial weight of the engine, this will prevent the engine from moving during fitting.
- Page 9 Page 9 of 21 CP0444 • Apply very light pressure to the underside of the engine to support the engine during the fitment process. Assemble the crash protectors before removing the engine bolts to limit the amount of time the engine is partially un-supported.
- Page 10 Page 10 of 21 CP0444 • Slide one of the smaller 10mm plain washers (item 8) onto one of the M10x45mm long cap headed bolts (item 7) so the washer sits against head of bolt as shown in picture 30. place the bolt assembly through the unthreaded hole in the mounting plate as shown in picture 31.
- Page 11 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty goods. NOTICE DE MONTAGE POUR CP0444 PROTECTIONS CRASH E KIT CONTIENT LES ARTICLES ILLUSTRES ET ETIQUETES SUR LA PAGE...
- Page 12 Page 12 of 21 CP0444 MANIERE DE LE MONTER SUR LA MOTO SI DES RONDELLES EN CAOUTCHOUC SONT UTILISEES POUR MAINTENIR LES COMPOSANTS SUR LES BOULONS ELLES PEUVENT ETRE JETEES NOTICE DISPONIBLE AU TELECHARGEMENT SUR : WWW.RG-RACING.COM OUTILS REQUIS VALEURS DE SERRAGE M4 BOULON = 8Nm CLÉ...
- Page 13 Page 13 of 21 CP0444 ORIENTATION DE LA PROTECTION CRASH VUE D’ENSEMBLE CÔTÉ GAUCHE & DROITE GAUCHE DROITE R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email:...
- Page 14 Page 14 of 21 CP0444 Photo 1 Photo 2 Photo 3 Photo 4 Photo 5 Photo 6 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...
- Page 15 Page 15 of 21 CP0444 Photo 7 Photo 8 Photo 9 Photo 10 Photo 11 Photo 12 Photo 13 Photo 14 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com...
- Page 16 Page 16 of 21 CP0444 Photo 15 Photo 16 Photo 17 Photo 18 Photo 19 Photo 20 Photo 21 Photo 22 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com...
- Page 17 Page 17 of 21 CP0444 Photo 23 Photo 24 Photo 25 Photo 26 Photo 28 Photo 27 Photo 29 Photo 30 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com...
- Page 18 Page 18 of 21 CP0444 Photo 31 Photo 32 Photo 34 Photo 33 Photo 36 Photo 35 Photo 37 Photo 38 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com...
- Page 19 Page 19 of 21 CP0444 NOTICE DE MONTAGE Avant de retirer les boulons du moteur, assurez-vous que la moto soit en position verticale et soutenue par un support moteur ou un cric approprié placé sous le carter de la moto pour supporter le poids partiel du moteur, cela empêchera le moteur de bouger pendant le...
- Page 20 Page 20 of 21 CP0444 • Placez l'écrou conique dans l'extrémité conique de l'extenseur et engagez le boulon jusqu'à ce que les faces s'engagent comme indiqué sur les photos 32 et 33 (la goupille anti-rotation installée s'insère dans l'une des fentes de l'entretoise expansible).
- Page 21 Page 21 of 21 CP0444 • Faites ensuite glisser le boulon avec les rondelles à travers l'une des protections crash (article 5) de manière à ce que la tête du boulon et les rondelles pénètrent dans le contre-alésage de la protection, comme indiqué...