1. Manuels
  2. Marques
  3. R&G Manuels
  4. Accessoires de moto
  5. CP0405BL
  6. Instructions de montage

R&G CP0405BL Instructions De Montage

Masquer les pouces

Publicité

Les langues disponibles

Les langues disponibles

Table des Matières

CP0405
FITTING INSTRUCTIONS FOR CP0405BL
AERO CRASH PROTECTORS FOR HONDA CBR500R '16- NON-DRILL KIT
Picture A
Picture B
THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED BELOW.
DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT.
Please note that the way the kit is packed does not necessarily represent the way of mounting to the
bike.
T
(
).
HE PARTS SHOWN MAY BE REPRESENTATIVE ONLY
FOR CLARITY OF INSTRUCTIONS ONLY
LEFT SIDE
R&G Racing
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
www.rg-racing.com
Email:
info@rg-racing.com

Publicité

Table des Matières
loading

Manuels Connexes pour R&G CP0405BL

Sommaire des Matières pour R&G CP0405BL

  • Page 1 CP0405 FITTING INSTRUCTIONS FOR CP0405BL AERO CRASH PROTECTORS FOR HONDA CBR500R ‘16- NON-DRILL KIT Picture A Picture B THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED BELOW. DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT. Please note that the way the kit is packed does not necessarily represent the way of mounting to the bike.

  • Page 2: Right Side

    CP0405 RIGHT SIDE LEGEND ITEM 1 = MOUNTING BLOCK (M0479) (x1). ITEM 2 = M6 x 35mm LONG BUTTON HEAD BOLTS (x4). ITEM 3 = SPACER (S0957 – 45mm LONG) (x1). ITEM 4 = CRASH PROTECTOR (B0431 with CS341 & S0255) (x2). ITEM 5 = LOCK-WASHERS (LW0001) (x2).
  • Page 3 CP0405 TOWARDS REAR TOWARDS FRONT OF BIKE OF BIKE PICTURE C GENERAL TORQUE SETTINGS M4 BOLT = 8Nm M5 BOLT = 12Nm M6 BOLT = 15Nm M8 BOLT = 20Nm M10 BOLT = 40Nm Picture 1 Picture 2 Picture 3 Picture 4 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ...
  • Page 4 CP0405 Picture 5 Picture 6 Picture 7 Picture 8 Picture 9 Picture 10 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...
  • Page 5 CP0405 Picture 11 Picture 12 Picture 13 Picture 14 Picture 15 Picture 16 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...
  • Page 6 CP0405 Picture 17 Picture 18 Picture 19 Picture 20 Picture 21 Picture 22 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...
  • Page 7 CP0405 Picture 23 Picture 24 Picture 25 Picture 26 Picture 27 Picture 28 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...

  • Page 8: Fitting Instructions

    CP0405 FITTING INSTRUCTIONS  To fit the crash protectors to the bike, the side fairings on both sides of the bike need to removed.  To remove the fairing on the left side of the bike, start by removing the three bolts that are arrowed in picture 1 and shown in pictures 2, 3 &...
  • Page 9 CP0405  The fairings can now be re-fitted to both sides of the bike, in the reverse procedure of how they were removed. Please ensure to re-connect the indicators when re-fitting.  To fit the left side crash protector, slide one of the 10mm washers (item 6) onto the M10 x 105mm long hex head bolt (item 7) so the washer sits against head of bolt.
  • Page 10 CP0405 have been modified or used or maintained otherwise than in accordance with R&G’s or manufacturer’s instructions and good engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned.
  • Page 11 CP0405 NOTICE DE MONTAGE CP0405BL PROTECTIONS CRASH LATERALES HONDA CBR500R ‘16- KIT SANS PERCAGE Photo A Photo B E KIT CONTIENT LES ARTICLES EXPOSES CI DESSOUS VERIFIER QUE TOUTES LES PIECES SOIENT PRESENTES AVANT DE PROCEDER AU MONTAGE A FAÇON DONT LE KIT EST EMBALLE NE CORRESPOND PAS FORCEMENT A LA FAÇON DE MONTER...
  • Page 12 CP0405 COTE GAUCHE COTE DROIT LEGENDE ARTICLE 1 = BLOC DE MONTAGE (M0479) (x1). ARTICLE 2 = M6 x 35mm BOULONS (x4). ARTICLE 3 = ENTRETOISE (S0957 – 45mm DE LONG) (x1). ARTICLE 4 = PROTECTION CRASH (B0431avec CS341 & S0255) (x2). ARTICLE 5 = RONDELLES DE BLOCAGE (LW0001) (x2).

  • Page 13: Couples De Serrage

    CP0405 ARRIERE MOTO AVANT MOTO PHOTO C COUPLES DE SERRAGE M4 BOULON = 8Nm M5 BOULON = 12Nm M6 BOULON = 15Nm M8 BOULON = 20Nm M10 BOULON = 40Nm Photo 1 Photo 2 Photo 3 Photo 4 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com...
  • Page 14 CP0405 Photo 5 Photo 6 Photo 7 Photo 8 Photo 9 Photo 10 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...
  • Page 15 CP0405 Photo 11 Photo 12 Photo 13 Photo 14 Photo 15 Photo 16 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...
  • Page 16 CP0405 Photo 17 Photo 18 Photo 19 Photo 20 Photo 21 Photo 22 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...
  • Page 17 CP0405 Photo 23 Photo 24 Photo 25 Photo 26 Photo 27 Photo 28 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...
  • Page 18 CP0405 NOTICE DE MONTAGE  Pour monter les protections crash sur la moto, les carénages latéraux des 2 cotés de la moto doivent être enlevés.  Pour enlever le carénage du coté gauche de la moto, commencez par enlever les 3 boulons indiqués sur la photo 1 et photos 2, 3 &...
  • Page 19 CP0405  Les carénages peuvent à présent être remontés de chaque coté de la moto, selon le procédé inverse de leur démontage. Veillerà reconnecter les clignotants lors du remontage.  Pour monter la protection crash du coté gauche, glisser une rondelle 10mm (article 6) sur le boulon M10 x 105mm (article 7) pour que la rondelle se place contre la tête du boulon.
  • Page 20 CP0405 Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise than in accordance with R&G’s or manufacturer’s instructions and good engineering practice or if the defect arises from accident or neglect.

Table des Matières