Publicité
34 | English
Checking (see figure S1)
– Set an angle gauge to 90° and position it between the
fence (14) and the saw blade (12) on the saw table (16).
The leg of the angle gauge must be flush with the saw blade
(12) along its entire length.
Setting (see figure S2)
– Loosen all four set screws (58) with a cross-headed
screwdriver and turn the saw table (16) together with the
scale (18) until the leg of the angle gauge is flush with the
saw blade along its entire length.
– Re-tighten the screws.
If the angle indicator (24) is not aligned with the 0° mark on
the scale (18) following adjustment, loosen the screw (57)
using a cross-headed screwdriver and align the angle indic-
ator along the 0° mark.
Transport (see figure T)
Before transporting the power tool, the following steps must
be carried out:
– Loosen the locking screw (32) if it is tightened. Pull the
tool arm fully forwards and retighten the locking screw.
– Make sure that the depth stop (31) is pressed all the way
in and that the adjusting screw (4) fits through the recess
without touching the depth stop when moving the tool
arm.
– Bring the power tool into the transport position.
– Remove all accessories that cannot be securely fitted to
the power tool. If possible, transport unused saw blades
in an enclosed container.
– Wind up the mains cable and tie it together with the hook-
and-loop strap (59).
– Carry the power tool by the transport handle (3) or hold it
by the recessed handles (27) on the sides of the saw
table.
Only use the transport devices to transport the power
u
tool and never the protective devices.
Maintenance and Service
Maintenance and Cleaning
Pull the plug out of the socket before carrying out any
u
work on the power tool.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.
The retracting blade guard must always be able to move
freely and retract automatically. It is therefore important to
keep the area around the retracting blade guard clean at all
times.
Always remove dust and chips after working by blowing out
with compressed air or using a brush.
Clean the guide roller (6) regularly.
1 609 92A 8L9 | (03.03.2023)
To clean the laser unit, turn the laser cover (60) outwards
and remove the dust with a paintbrush (see figure U).
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
You can find further service addresses at:
www.bosch-pt.com/serviceaddresses
Disposal
The power tool, accessories and packaging should be re-
cycled in an environmentally friendly manner.
Do not dispose of power tools along with
household waste.
Only for EU countries:
According to the European Directive 2012/19/EU on Waste
Electrical and Electronic Equipment and its implementation
into national law, power tools that are no longer usable must
be collected separately and disposed of in an environment-
ally friendly manner.
If disposed incorrectly, waste electrical and electronic
equipment may have harmful effects on the environment and
human health, due to the potential presence of hazardous
substances.
Only for United Kingdom:
According to The Waste Electrical and Electronic Equipment
Regulations 2013 (SI 2013/3113) (as amended), products
that are no longer usable must be collected separately and
disposed of in an environmentally friendly manner.
Bosch Power Tools
Publicité
