Publicité
However, there is MUCH more to it than may be explained here.
Therefore, we strongly encourage you to review the full owner's manual
on the Mackie website should any additional questions arise.
1. Power Connector & Switch Connect the supplied AC
power cord to this jack. The power switch turns the mixer
on and off. The Power LED will illuminate when powered.
2. 48V Phantom Power Switch Provides 48V for mics, affecting
all XLR jacks simultaneously. The +48V LED illuminates
when phantom power is engaged.
3. Combo Inputs Connect a balanced or unbalanced mic,
instrument or line-level signal using an XLR or 1/4"
connector.
4. XLR Inputs Connect a balanced mic or line-level signal
using an XLR connector.
5. Line Inputs Connect a balanced or unbalanced
line-level signal using a 1/4" connector.
6. 1/8" Input Connect an 1/8" line-level signal from
a smartphone, MP3 player, or other signal source.
7. Line/Hi-Z Switch Engage the switch to play a guitar
through channels 1-2 without using a DI Box.
8. Insert Connect a serial effects processor, such
as a compressor or gate, using a 1/4" Y cable.
9. Low Cut Switch Cuts bass frequencies below 100 Hz
at a slope of 18 dB per octave.
10. Gain Gain ajusts the mic/line input sensitivity.
11. Level Set LED Illuminates green to indicate signal.
12. Compressor Reduces the dynamic range of input signals.
13. Equalization Boost or cut the level at certain frequencies
to enhance the sound.
14. Bluetooth On/Off and Pair Switches Press the button to turn
the Bluetooth channel on and off. Press and hold to pair
with a Bluetooth device. The Bluetooth may disconnect
when affected by Electrostatic Discharge [ESD]. Manually
reconnect the Bluetooth connection.
15. Aux FX & FX Send Feeds the internal FX or an external
processor via the FX send jack. Each channel has its own
level control.
16. Pan Adjusts how much of the signal is sent to the left
and right outputs.
17. Mute Mutes the channel signal. The button illuminates
if the mute switch is engaged.
ProFX10 GO is not a difficult product to master.
FRONT & REAR PANEL DESCRIPTIONS
18. Channel Level Knob Adjusts the level to the main mix.
19. Main Out L/R Connect to the inputs of amplifiers, powered
speakers, or a serial effects processor.
20. CR Out L/R Feed the inputs of a control room amplifier,
studio monitors or a headphone distribution amplifier.
21. FX Footswitch Connect a footswitch to mute or un-mute
the internal effects.
22. Phones Connect stereo headphones here.
23. Preset Selector and Display Turn the preset selector to
choose an effect. The display shows the number of the
currently selected effects preset.
24. Main Meters Used to gauge the input and output levels
to ensure that the signals are not clipping.
25. CR/Phones Controls the control room and headphones
levels.
26. Break Switch and LED Mutes all channel inputs.
27. FX Return Knob Adjusts the level of the stereo output
from the internal FX processor being added to the main mix.
28. Blend Knob Provides a balance of the channel inputs (left)
and USB 1-2 return (right).
29. To Phones / Control Room Switch Routes a mix of the inputs
and USB 1-2 to CR/phones outs. Mutes main mix in CR/
phones outs when engaged.
30. Main Mix Adjusts the level of the signal sent to the main
outputs.
31. USB I/O A 2x4 interface allowing you to stream audio
to and from the mixer via computer.
32. USB 3/4 Switch Engaging this switch mutes the 1/8" input,
allowing the USB return to flow through the channel instead.
33. Back Button Press this button to return to the previous
screen.
34. Record Press the REC button to toggle between the
recording modes.
Battery Compartment The bottom panel contains the ProFX10
GO battery compartment. Push the tab to release and replace.
9
Quick Start Guide
Publicité
