Publicité
Mounting (Optional) / 安装固定（可选）
Super Fast Charger
MAX 24W
AC
POWER 1000
AC
4
ON/开机
EN
Mounting (Optional)
Install and mount the product on the car frame as shown in the figure, based on actual use.
• Avoid mounting the product in areas with high temperatures or prone to impact.
• Make sure to install, operate, or store the product in a well-ventilated and sheltered environment
away from children and pets.
• DO NOT install or operate the product in an environment that is humid, contains corrosive liquids,
or is at risk of fire or explosion.
Installation and Usage
• Before installing, make sure the power station is updated to the latest firmware version, power off
the device and disconnect the power supply.
• It is recommended that the installation process is performed by a professional. Avoid routing
cables in areas with high temperatures, where there are sharp objects, or where friction may
occur. Secure the cables properly to avoid cable wear or loose connection.
• Refer to the specifications of the car battery to make sure that the car battery and cables are
compatible with this product. Follow the safety guidelines of the car battery.
• DO NOT start the car or use the product until the installation process is completed.
1. Remove the washers and screws on the car charging terminals of the super fast charger using a
Philips screwdriver.
Connect the round terminals with protective covers of the car charging cable to the super fast
charger. Connect the round terminal (red) to the positive terminal (+) and the round terminal (black)
to the negative terminal (-). Re-install the washers and the screws and tighten the screws. Route the
cables inside the car.
2. Connect the car charging cable and the fuse cable (red) to the car battery:
a. Connect the round terminal of the fuse cable (red) to the positive terminal (+) of the car battery.
b. Connect the other end of the fuse cable to the round terminal (red) of the car charging cable. Make sure
the round terminal, the washer, and the nut are in the correct sequence and securely tightened.
c. Connect the round terminal (black) of the car charging cable to the negative terminal (-) of the car
battery.
3. Use the SDC cable of the super fast charger to connect to the power station or the expansion battery
as shown in the figure.
4. Toggle the power switch to power on the super fast charger. The status indicator shows solid green
after powering on. Press and hold the mode switch button to switch the mode. The solid-green
indicator shows the current mode.
•
Recharge Mode: The power station and the expansion battery will be charged.
•
Charging Mode: The power station and the expansion battery will supply power to the car
battery to avoid over-discharging.
• Users can link the power station to the DJI Home app and view the device information or modify
settings in the app.
Specifications
Model
Temperature
Recharging
Power Supply
Red
红
Car Charging Cable
车充连接线
闪充
SDC
SDC
SDC
SDC
CHARGE
MAX 140W
1200
600
W
W
CHARGE
MAX 24W
MAX 140W
1200
600
W
W
POWER 1000
DYS_DC1000
Discharging: -10° to 45° C (14° to 113° F)
Recharging: 0° to 45° C (32° to 113° F)
Car Charging Terminals (input): 12-45 V DC (rated), max 70 A, max 1000 W
SDC Cable (output): 40-58.4 V DC
SDC Cable (input): 40-58.4 V DC
Car Charging Terminals (output):
12V Car System: 11-14.4 V DC, max 1000 W
24V Car System: 22-28.8 V DC, max 1000 W
1
2
b
c
Black
黑
3
MAX 24W
MAX 140W
AC
POWER 1000
Black
黑
Fuse Cable (Red)
红色保险线
a
CHARGE
1200
600
W
W
Red
红
2s
2
Publicité
