Télécharger Imprimer la page

AKG Acoustics WMS 400 Mode D'emploi page 31

Masquer les pouces Voir aussi pour Acoustics WMS 400:

Publicité

NAME
"DIANE"
NAME
">D<IANE"
NAME
"J>I<ANE"
NAME
">JONI_ _<"
SAVE >Y<
SAVE >N<
>X-TRA<
>X-TRA<
NAME
NAME
"JOANIE"
"DIANE"
Section 3.9.1 applies to both the HT 400 handheld transmitter and the PT 400 bodypack transmitter. To set
the audio input gain on the HT 400, use the TX Gain screen on the receiver and the infrared connection.
To set the audio input gain on the PT 400, use the gain control in the transmitter battery compartment.
PRG IR
IR
>PRG IR<
IR
>I>---<
IR OK
IR ERR
IR
IR
IR
>RETRY<
IR
>TXGAIN<
TXG >HI<
>PRG IR<
IR
>I>---<
IR OK
IR ERR
IR
IR
IR
>RETRY<
IR
WMS 400 V 1.10
All manuals and user guides at all-guides.com
This screen lets you edit the current
name of the receiver. If you have stored
no name for the receiver yet or deleted
its previous name, this screen will not
be available. The EXTRA screen, how-
ever, allows you to save a new name at
any time (refer to section 4.1.3).
The receiver name may be any combi-
nation of up to six letters and/or num-
bers.
Use
ter.
Use
acter, etc....
... to the sixth character.
>DELETE<
SAVE >Y<: save your setting.
>X-TRA<
SAVE >N<: reject your setting.
>DELETE<: delete all names.
EXTRA
X-TRA
To program the transmitter for the same
frequency you selected on the receiver:
1. Switch power to the receiver on.
2. Set the ON-MUTE/PRG-OFF switch
(19) on the transmitter to "OFF". The
>EXIT<
status LED (20) will extinguish.
3. Set the ON-MUTE/PRG-OFF switch
(19) to "MUTE/PRG". The display will
alternately indicate the currently
selected frequency and "Prg IR". The
status LED (20) remains dark.
4. Refer to Diagram 6.
5. Point the infrared sensor (1) on the
transmitter at the infrared emitter (2)
on the receiver from a distance of
4 inches (10 cm) max.
TXBAND
IR
IR OK: The transmitter has been tuned
to the same frequency as the receiver.
IR ERR: The data transmission has
failed (no communication).
>EXIT<
TXBAND: The frequency bands of the
transmitter and receiver are not identical
or the transmitter RF output is too
high/low.
PRG IR/
3.8.1/2/3
1. Switch power to the receiver on.
2. Set the ON-MUTE/PRG-OFF switch
(19) on the transmitter to "OFF". The
status LED (20) will extinguish.
TXG >LO<
3. Set the ON-MUTE/PRG-OFF switch
(19) to "MUTE/PRG". The display will
alternately indicate the currently
selected frequency and "Prg IR". The
status LED (20) remains dark.
4. Refer to Diagram 7.
5. Select "HI" for an HT 400/D or "LO"
for an HT 400/C.
6. Point the infrared sensor (1) on the
transmitter at the infrared emitter (2)
on the receiver from a distance of
TXBAND
4 inches (10 cm) max.
IR
IR OK: The transmitter has been
adjusted to the selected gain setting.
IR ERR: The data transmission has
>EXIT<
failed (no communication).
TXBAND: The frequency bands of
the transmitter and receiver are not
identical or the transmitter RF output
>TXGAIN<
is too high/low.
and
to select the first charac-
and
to select the second char-
3 Setting Up
3.8.4 Editing the Receiver
Name
Note:
Diagram 5: Editing the receiver
name.
3.9 Setting Up the Transmitter
Note:
3.9.1 Frequency
Refer to figs. 3 (page iv) and 4
(page iii).
Refer to figs. 10 (handheld trans-
mitter) and 11 (bodypack transmit-
ter) on page vi.
Diagram 6: Setting the transmitter
carrier frequency.
3.9.2 Handheld Transmitter
Input Gain
Refer to fig. 10 on page vi.
Diagram 7: Setting the audio input
gain on the handheld transmitter.
25

Publicité

loading