Publicité
14
| English
ulty or worn-out parts must always be replaced
and not repaired. Only use original spare parts.
WATER TRAP WITH FILTER
When the trapped water level reaches the upper
limit of the water trap (Fig. 1.9), drain immediately
by pulling down the metal tube at the bottom of
the water trap.
DRAINING THE TANK
1. Ensure that the ON/OFF switch is in the OFF
position and disconnect the product from it's
power source.
2. Place a suitable container underneath the drain
valve (Fig. 1.6) to catch all of the water conden-
sation.
3. Slowly open the draining valve.
4. Fully drain the water condensation.
5. Close the drain valve.
POWER CABLE
To avoid shock or fire hazard, if the power cable is
worn or cut, or damaged in any way, have it repla-
ced immediately. Electrical connection cables of-
ten suffer insulation damage. Possible causes are:
1. Punch points when connection cables are run
through window or door gaps.
2. Kinks resulting from incorrect attachment or
laying of the connection cable.
3. Cuts resulting from running over the connec-
ting cable.
4. Insulation damage resulting from forcefully
pulling out of the wall socket.
5. Cracks through aging of insulation.
Such defective electrical connection cables must not
be used as the insulation damage makes them extre-
mely hazardous.
OIL CHANGE
WARNING
Checking the level and changing the oil should
be done on solid and level ground. The product
has to be deactivated and disconnected from it's
power source at all times. If the compressor had
been running, it will be hot and the procedure
should be done with care and necessary precauti-
ons in order to avoid burn danger.
To check the oil level:
1. Look through the oil sight glass. The oil level
should reach the red dot.
2. If required, add enough oil through the oil filler
neck to bring the oil level to the red dot on the
oil sight glass.
To change the oil:
1. Remove the oil breather cap.
2. Place a suitable container under the oil sight
glass to catch the used oil.
3. Remove the oil sight glass by turning it coun-
terclockwise.
4. Fully drain the oil.
5. Reposition the oil sight glass and tighten
appropriately.
6. Gradually add enough oil through the oil filler
neck to bring the oil level to the red dot on the
sight glass.
7. Reposition the oil breather cap and tighten
appropriately.
NOTE
If the product frequently works under extremely
dusty or other severe conditions, change the oil
more frequently.
CLEANING
Use a small soft brush to clean the outside of the
product. Do not use strong detergents. House-
hold cleaners that contain aromatic oils such as
pine and lemon and solvents can damage plastic
housing or handle. Wipe off any moisture with a
soft cloth. Remove dust, dirt and machining resi-
dues with an appropriate vacuum cleaner if ne-
cessary.
STORAGE
In case the product will be stored for an extended
time, use the following storage procedure:
1. Turn off the product and disconnect it from it's
power source.
2. Remove all connected accessories and tools
from the air outlet.
3. Drain the tank, using the drain valve.
4. Thoroughly clean and inspect for any loose or
damaged parts. Repair or replace damaged
parts and tighten loose screws, nuts or bolts.
5. Lubricate and apply grease, where required.
6. Store in original packaging.
7. Store the product only in dry and well ventila-
ted place.
ENVIRONMENTAL PROTECTION
This product must not be disposed together with
domestic waste in compliance with relative legis-
lation concerning waste of electrical and elec-
tronic equipment where applicable. Recycle raw
materials instead of disposing as waste. Product,
accessories and packaging should be sorted for
environment friendly recycling. By properly dis-
posing this product, you are also contributing to
the effective use of natural resources.
You can obtain information on collection points
for waste equipment from your municipal admi-
nistration, public waste disposal authority, an
authorized body for the disposal of waste electri-
cal and electronic equipment or your waste dispo-
sal company.
WARRANTY
This product is warranted in accordance with the
legal / country specific regulations, effective from
the date of purchase by the first user. Consult
your authorized dealer for disassembly and servi-
ce, not covered in this manual. In case of a claim,
please send the product, completely assembled,
to your dealer or the official service center.
Warranty covers the cost of repairing the product
and any required replacement of parts that are
defective in terms of material or manufacturing
and does not apply:
Where repairs have been made or attempted by
f
Publicité
