Publicité
GB
IE
FLOOR PUMP
Instruction Manual
Introduction ..............................................................8
Intended use .............................................................8
Package contents .....................................................8
Technical data ..........................................................8
Attention safety instructions .....................................8
Initial use of the floor pump ....................................9
Adapter.....................................................................9
Cleaning & care instructions ................................ 10
Disposal ................................................................. 10
Warranty ............................................................... 10
Warranty terms ..................................................... 10
Distributor .............................................................. 10
Service address .................................................... 10
Introduction:
Congratulations!
With your purchase you have chosen a high-
quality product. Make yourself familiar with the
product before starting to use it. Carefully read the
following instruction manual. Use the product only
as described and only for the specified areas of
application. Keep this instruction manual for future
reference. When transferring this product to third
parties, also include all documents.
Symbols in these operating & assem-
bly instructions, and on the packaging:
!
This symbol indicates a risk of injury.
!
This is how additional information is ear-
marked.
This symbol will inform you about the dis-
posal of the packaging and product.
!
Intended use:
This floor pump is suitable for inflating all conven-
tional bicycle tyres. Other uses or modifications to
the product are considered non-intended usage
and can lead to risk of injury and damages. The
distributor bears no liability for damages result-
8
ing from non-intended usage. The product is not
intended for commercial use.
Package contents:
(A1 / A2)
1 x floor pump
1 x metal adapter for balls,
2 x plastic adapters for air mattresses, inflatable
toys, etc.
1 x instruction manual
Technical data:
Type: Floor Pump
IAN 298839_1904
Item-/Monz-No: 26235
Project: PO30000497
Nominal pressure: 7 bar / 100 PSI
Maximum allowable pressure: 8 bar / 116 PSI
Displacement: 370 ml / 370 cm³
Pressure hose length: 100 cm
Production date: 2019
Warranty: 3 years
!
Attention safety instructions!
ATTENTION! RISK OF DEATH AND
INJURY.
Keep packaging material away from children.
There is a risk of suffocation and other injuries!
- You can inflate all bicycle tires up to the floor
pump's indicated maximum allowable pressure
(max. 8 bar / 116 PSI) or to the tyre manufac-
turer's indicated maximum tyre pressure. This
can usually be found on the tyre wall. The indi-
cated maximum values may not be exceeded at
any time.
Warning! Risk of injury through explosion
if maximum permitted pressure values are
exceeded.
- Defective or damaged air pumps may no
longer be used due to risk of injury. Defective
Floor pumps must be properly disposed of.
Repairs are not possible.
- Floor pumps with damaged connection parts
or other defects or damage may no longer be
used due to risk of injury. Defective floor pumps
must be disposed of correctly. Repair is not pos-
sible.
Warning! Damaged floor pump, hose,
adapter or faulty connectors cause risk of
explosion.
- Due to the high operating force and the risks
associated with this, the product is not suited for
use by children or persons with physical and/or
mental disabilities.
Warning! Please note that the pump
plunger and pump cylinder become very
hot over longer periods of pumping due to the
friction between them. For this reason, you
should only grasp the floor pump on the pump
handle after pumping in order to avoid burns.
- Due to the risk of injury, a defective or dam-
aged floor pump may never be used.
Warning! Some bicycle valves do not
allow pressure display. For your own safety,
please check the air pressure with a calibrated
manometer (i.e. at a fuel station).
Initial use of the floor pump:
(B1-B5)
(B1) Place the floor pump on a level and stable
surface.
(B2) There must be no kinks in the pump hose.
(B3) During pumping, please always position
yourself with both feet on the foot plate of the
floor pump to ensure it won't fall over.
(B4) Operate the pump handle in a smooth and
even manner and not too quickly.
!
(B5) There is a red pointer in the middle of
the manometer. This red pointer can serve as an
optical mark for the desired pressure.
Turn the red pointer to the desired pressure dis-
play for this purpose.
Please note that the set mark only serves as orien-
tation and does not influence the air pressure!
Adapter:
(C1)
The floor pump has been provided with a
pump head with a reversible valve adapter. As
delivered, the pump head has been set to use the
SCHRADER (large opening) adapter. To switch
to using the DUNLOP/PRESTA adapter (smaller
opening), flip the lever (A) upwards horizontally.
Do NOT pull the lever. Unscrew the valve adapter
from the pump head. Turn the valve adapter so
that the larger opening will be screwed into the
pump head (b).
Note: screw the valve adapter slowly onto
the pump head to prevent it from tilting during
screwing.
Adapter: (C1)
(1) E.g. balls
(2) E.g. air mattresses
(3) E.g. inflatable boats
(4) To inflate inner tubes with schrader valves
e.g. mountain bikes, trolleys and trailers.
(5) To inflate inner tubes with dunlop valves,
e.g. city/trekking bicycles
(6) For inflating inner tubes with a presta valve,
e.g. on racing bicycles and mountain bikes.
(7) Pump head (To lock in place, please fold
down the lever of the pump head.)
(Valves (4), (5), (6) not included)
Inflating tyres with a schrader valve: (C2)
First remove the dust protection cap (1). Insert the
pump head with the large opening into the valve
(2). To lock in place, please fold down the lever of
the pump head (3).
Inflating tyres with a dunlop valve: (C3)
First remove the dust protection cap (1). Insert the
pump head with the small opening into the valve
(2). To lock in place, please fold down the lever of
the pump head (3).
Inflating tyres with a presta valve: (C4)
First remove the dust protection cap (1). Detach
the valve nut (2a-2c). Insert the pump head with
the small opening into the valve (3). To lock in
place, please fold down the lever of the pump
head (4).
Inflating air mattresses, inflatable toys,
etc.: (C5)
First open the valve plug (1). Select the appropri-
ate plastic adapter and insert it into the large
opening of the pump head (2). To lock in place,
please fold down the lever of the pump head (3).
Now insert the plastic adapter into the object to
be inflated (4).
Inflating balls: (C6)
Insert the metal adapter in the large opening of
the pump head (1). To lock in place, please fold
down the lever of the pump head (2). Now insert
the metal adapter into the ball (3).
9
Publicité
